GM Service Manual Online
For 1990-2009 cars only

Diagnostic Aids

    • Verify that the fuel level is in the same range as the customer concern.
    • For intermittent diagnosis, refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
    • Refer to Fuel Level Specifications in order to verify the correct fuel level sensor readings. The Fuel Level Sensor parameter is available on the scan tool in the PCM data list.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests for a high resistance in the signal circuit and the low reference circuit of the fuel level sensor.

  2. DTCs will be set in the PCM when you perform this diagnostic table.

Step

Action

Value(s)

Yes

No

Schematic Reference: Instrument Cluster Schematics

Connector End View Reference: Instrument Panel, Gages, and Console Connector End Views , Powertrain Control Module Connector End Views in Engine Controls-4.3L, or Inline Harness Connector End Views in Wiring Systems.

1

Did you perform the Instrument Cluster Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Instrument Cluster

2

  1. Disconnect C310.
  2. Connect the J 33431-C Signal Generator and Instrument Panel Tester between the signal circuit of the fuel level sensor and the low reference circuit of the fuel level sensor on the male terminal side of the connector.
  3. Turn the ignition ON , with the engine OFF.
  4. Important: Verify the J 33431-C resistance settings with a DMM.

  5. Vary the resistance on the J 33431-C from 40-250 ohms.
  6. Refer to Fuel Level Specifications in order to convert from resistance to fuel gage display.

Does the fuel gage display the correct fuel level?

--

Go to Step 4

Go to Step 3

3

  1. Install a scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. Important: Verify the J 33431-C resistance settings with a DMM.

  4. Vary the resistance on the J 33431-C from 40-250 ohms.
  5. Refer to Fuel Level Specifications in order to convert from resistance to fuel level percent.
  6. Important: Turn the ignition OFF momentarily between the resistance settings in order to quickly update the scan tool display.

  7. With the scan tool, observe the Fuel Level Sensor parameter in the PCM Enhanced EVAP Data list.

Does the Fuel Level Sensor parameter display the correct fuel level?

--

Go to Step 11

Go to Step 5

4

Inspect for the following items:

    • A poor connection at the harness connector of the fuel level sensor
        Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
    • A misaligned fuel level sender
    • A deformed fuel tank
    • A high resistance in the signal circuit or low reference circuit of the fuel level sensor between the fuel level sensor and C310.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 7

5

Test the signal circuit of the fuel level sensor for a high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 6

6

Test the low reference circuit of the fuel level sensor for a high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 9

7

  1. Remove the fuel level sender.
  2. Inspect for the following items:
  3. • A stuck fuel level sender such as the fuel strainer interfering with the sender float arm
    • Foreign material in the fuel tank such as ice

Did you find and correct the condition?

--

Go to Step 13

Go to Step 8

8

  1. With the J 39200 DMM, measure the resistance of the fuel level sensor while moving the float arm.
  2. Observe both the analog and digital displays on the DMM.

Does the resistance change smoothly across the specified range?

40-250 ohms

Go to Diagnostic Aids

Go to Step 10

9

Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 12

10

Replace the fuel level sender. Refer to Fuel Level Sensor Replacement in Engine Controls.

Did you complete the replacement?

--

Go to Step 13

--

11

Replace the IPC. Refer to Instrument Cluster Replacement .

Did you complete the replacement?

--

Go to Step 13

--

12

Important: Program the replacement PCM.

Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls.

Did you complete the replacement?

--

Go to Step 13

--

13

  1. Use the scan tool in order to clear the PCM DTCs.
  2. Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 2