GM Service Manual Online
For 1990-2009 cars only

Object Number: 365051  Size: MF
ABS Components
Antilock Brake System Schematics Non VE1

Circuit Description

The EBCM receives the rear wheel speed signal from the Vehicle Control Module (VCM). The rear wheel speed signal originates from the Vehicle Speed Sensor (VSS) which is connected to the VCM.

Conditions for Setting the DTC

EBCM losing the rear wheel speed signal for at least 5 seconds while the vehicle is moving above 13 km/h (8 mph) with the brake pedal released.

Action Taken When the DTC Sets

    • The ABS indicator lamp turns on
    • The ABS disables

DTC C0236 is a Condition Latched DTC, which indicates that the above actions remain true only as long as the condition persists.

DTC C0236 is a DRP Critical DTC, which means that DRP is disabled and the BRAKE indicator lamp will also light.

Conditions for Clearing the DTC

    • Repair the conditions responsible for setting the DTC
    • Use the Scan Tool Clear DTCs function.
    • A Condition Latched DTC may exist momentarily, or constantly. In either case, the DTC will be stored in the EBCM memory until it is repaired, and/or the DTC is cleared. After the DTC is repaired and/or cleared and the ignition is turned to ON, the ABS lamp will remain lit until the EBCM completes a power-up self test. This test concludes when the vehicle has reached a speed of greater than 13 km/h (8 mph) and the wheel speed inputs have been checked by the EBCM.

Diagnostic Aids

Using the Scan Tool, check for any powertrain DTCs. Resolve any powertrain DTCs before starting with this DTC table.

This DTC can be set by a faulty EBCM or a fault in CKT 1827.

In addition, any of the following conditions may cause an intermittent malfunction:

    • A poor connection
    • Wire insulation that is rubbed through
    • A wire breaks inside the insulation

Thoroughly check any circuitry that is suspected of causing the intermittent complaint for the following conditions:

    • Backed out terminals
    • Improper mating
    • Broken locks
    • Improperly formed or damaged terminals
    • Poor terminal to wiring connections
    • Physical damage to the wiring harness

If the customer says that the ABS indicator lamp is on only during humid conditions such as rain, snow, or vehicle wash, then thoroughly inspect the suspected circuits for signs of water intrusion. Use the following procedure:

  1. Spray the suspected area with a 5% salt water solution (two teaspoons of salt to 12 oz. of water)
  2. Drive the vehicle above 24 km/h (15 mph) for at least 30 seconds

If the DTC returns, replace the suspected harness.

Test Description

The numbers below refer to the steps in the diagnostic table:

  1. This step uses the voltage output from the VCM to check the 1827 CKT.

  2. This step checks the 1827 CKT for proper resistance.

  3. This step checks for a short in the wiring between the ECBM and the VCM.

Step

Action

Value(s)

Yes

No

1

Was the Diagnostic System Check performed?

--

Go to Step 2

Go to Diagnostic System Check - ABS

2

  1. Turn the ignition to OFF.
  2. Disconnect the 10-way EBCM harness connector from the EBCM.
  3. Turn the ignition to RUN.
  4. Using a J 39200 , measure the voltage at terminal E of the 10-way EBCM harness connector.

Is the voltage measurement within the specified range?

Greater than 10 volts

Go to Step 4

Go to Step 3

3

  1. Turn the ignition to OFF.
  2. Disconnect the VCM harness connector C1 from the VCM.
  3. Using a J 39200 , measure the resistance from terminal E of the 10-way EBCM harness connector to terminal 15 of the VCM harness connector C1.

Is the resistance measurement within the specified range?

0-2ohms

Go to Step 5

Go to Step 8

4

  1. Turn the ignition to OFF.
  2. Reconnect all connectors.
  3. Turn the ignition to RUN.
  4. Using a Scan Tool , clear DTCs.
  5. Test drive the vehicle above 24 km/h (15 mph).
  6. Use a Scan Tool to read DTCs.

Did the DTC set?

--

Go to Step 6

Go to Step 7

5

Using a J 39200 , measure the resistance from terminal E of the 10-way EBCM harness connector to ground.

Is the resistance measurement within the specified range?

OL

Go to DTC P0500 Vehicle Speed Sensor (VSS) Circuit

Go to Step 9

6

Replace the EBCM. Refer to Electronic Brake Control Module Replacement .

Is the repair complete?

--

Go to Diagnostic System Check - ABS

--

7

Malfunction is intermittent.

  1. Inspect all connectors and harnesses for damage which may result in high resistance when all components are connected.
  2. Refer to Diagnostic Aids for more information.

  3. Perform all necessary repairs.

Is the repair complete?

--

Go to Diagnostic System Check - ABS

--

8

Repair the open in CKT 1827.

Is the repair complete?

--

Go to Diagnostic System Check - ABS

--

9

Repair short to ground in CKT 1827.

Is the repair complete?

--

Go to Diagnostic System Check - ABS

--