CAMPAIGN: INOP. SEAT BELT MECH.- BUCKET SEATS (A95). GMC Truck GMC V Truck

Models: 1988 RV 10-20 Suburban with Bucket Seats (A95) and Gray Interior Trim (82I)

TO: ALL GENERAL MOTORS DEALERS

General Motors of Canada has determined that certain 1988 Suburbans equipped with bucket seats and gray interior trim may have an inoperable driver's seat and/or shoulder belt locking mechanism. In day-to-day usage of the lap/shoulder belt, a driver may not notice the problem. In the event of a crash, however, the affected belt(s) would not lock, but would totally unwind before it would restrain the driver, and therefore could increase the possibility of injury to the seat occupant.

To correct this condition, a new driver's seat belt assembly will be installed in each affected vehicle.

VEHICLES INVOLVED:

Involved are certain 1988 RV 10-20 Suburbans equipped with A95 and 82I built within the following VIN breakpoints:

Model Year Assembly Plant From Through ---------- -------------- ---- ------- 1988 Flint JF531205 JF531677

All affected vehicles have been identified by the VIN listing provided to involved Dealers with this bulletin. Any Dealer not receiving a listing was not shipped any of the affected vehicles.

DEALER CAMPAIGN RESPONSIBILITY:

Dealers are to service all vehicles subject to this campaign at no charge to owners, regardless of mileage, age of vehicle, or ownership, from this time forward.

Whenever a vehicle subject to this campaign is taken into your new or used vehicle inventory, or it is in your Dealership for service in the future, you should take the steps necessary to be sure the campaign correction has been made before reselling or releasing the vehicle.

Owners of vehicles recently sold from your new vehicle inventory are to be contacted by the Dealer, and arrangements made to make the required modification according to instructions contained in this bulletin.

CAMPAIGN PROCEDURE:

Refer to Section 4 of the Service Policies and Procedures Manual for the detailed procedure on handling Product Campaigns. Dealers are requested to complete the campaign on all transfers as soon as possible.

OWNER NOTIFICATION:

All owners of record at the time of campaign release are shown on the attached computer listing and have been notified by first class mail from General Motors. The listings provided are for campaign activity only and should not be used for any other purpose.

PARTS INFORMATION:

Parts required to complete this campaign should be ordered through regular channels, as follows:

Part Number Description Quantity/Vehicle ----------- ----------- ---------------- 15583507 Driver's Front Seat 1 Belt Assembly (Gray)

PARTS AND LABOUR CLAIM INFORMATION:

Credit for the campaign work performed will be paid upon receipt of a properly completed campaign claim card, RAPID terminal or DCS transmission in accordance with the following:

Repair Code Description Time Allowance ------------ ------------ --------------- 2A Replace Driver's Seat .5 Belt Assembly

Time allowance includes 0.1 hour for Dealer administrative detail associated with this campaign. Parts credit will be based on Dealer net plus 30% to cover parts handling.

SERVICE PROCEDURE:

Remove or Disconnect (Figure 1)

1. Upper seat belt anchor plate cover (42).

- Pry the top of the cover away from anchor plate.

2. Anchor plate bolt (36).

3. Anchor plate (35).

4. Retractor (44) to floor bolt (47).

5. Retractor (44) from vehicle.

6. Plug (51).

7. Buckle (43) to floor bolt (50).

8. Seat belt wire (41) (left side only).

9. Buckle (43) from floor.

Install or Connect (Figure 1)

1. Buckle (43) to floor.

2. Seat belt wire (41) (left side only).

3. Buckle (43) to floor bolt (50).

Tighten

- Bolt (50) to 50 N.m (37 ft. lbs.)

4. Plug (51).

5. Retractor (44) to the vehicle.

6. Retractor (44) to floor bolt (47).

Tighten

- Bolt to 50 N.m (37 ft. lbs.)

7. Anchor plate (35).

8. Anchor plate bolt (36).

Tighten

- Bolt to 50 N.m (37 ft. lbs.)

9. Upper seat belt anchor plate cover (42).

INSTALLATION OF CAMPAIGN IDENTIFICATION LABEL

Clean surface of radiator upper mounting panel and apply a Campaign Identification Label. Make sure the correct campaign number is inserted on the label. This will indicate that the campaign has been completed.

Dear General Motors Customer:

To correct this condition, a new driver's seat belt assembly will be installed in each affected vehicle. This service will be completed for you at no charge.

Instructions for performing this service have been sent to your General Motors Dealer. Please contact your Dealer to arrange a service date. The labour time necessary to perform this correction is 25 minutes. Please ask your Dealer how much additional time will be needed to process your vehicle.

This letter identifies your vehicle. Presentation of this letter to your Dealer will assist their Service personnel in completing the necessary correction to your vehicle in the shortest possible time.

Further assistance, if required, may be obtained from the General Motors Zone Office nearest you. Your vehicle Owner's Manual provides the location and phone number of each respective Zone Office.

We are sorry to cause you this inconvenience; however, we have taken this action in the interest of your continued satisfaction with our products.

Object Number: 84396 Size: FS

General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.