DTC P0140 HO2S Circuit Insufficient Activity Bank 1 Sensor 2. GMC Truck GMC Suburban

For 1990-2009 cars only

Makes 🢒 GMC_Truck 🢒 1998 🢒 GMC Suburban - 4WD 🢒 DTC 🢒 DTC P0140 HO2S Circuit Insufficient Activity Bank 1 Sensor 2

DTC P0140 HO2S Circuit Insufficient Activity Bank 1 Sensor 2 Under 8600 GVW without C6P

HO2S (5.7L) - Comp Loc Figure
HO2S Controls
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The heated oxygen sensor (HO2S) is a sensor designed to create a voltage relative to the oxygen content in the engine exhaust stream. The control module supplies the HO2S with signal high and low circuits. Ignition voltage and ground are supplied to the HO2S heater by independent circuits. The oxygen content of the exhaust indicates when the engine is operating lean or rich. When the HO2S detects that the engine is operating rich, the signal voltage is high, and decreases the signal voltage as the engine runs leaner. This oscillation above and below the bias voltage, sometimes referred to as activity or switching, can be monitored with the HO2S signal voltage.

The HO2S contains a heater that is necessary in order to quickly warm the sensor to operating temperature. The heater also maintains the operating temperature during extended idle conditions. The HO2S needs to be at a high temperature in order to produce a voltage. When the HO2S reaches operating temperature, the control module monitors the HO2S bias, or reference, voltage. It also monitors the HO2S signal voltage for Closed Loop fuel control. During normal Closed Loop fuel control operation, the control module will add fuel, or enrich the mixture, when the HO2S detects a lean exhaust content. The control module will subtract fuel, or "lean-out" the mixture, when the HO2S detects a rich exhaust condition.

Certain vehicle models utilize an oxygen sensor behind the catalytic converter in order to monitor catalyst efficiency.

This diagnostic trouble code (DTC) determines if the HO2S is functioning properly. It checks for an adequate number of HO2S voltage transitions above and below the bias range of 300-600 mV. This DTC sets when the vehicle control module (VCM) fails to detect a minimum number of voltage transitions above and below the bias range during the test period. Possible causes of this DTC are:

•	An open or a short to voltage on either the HO2S signal or HO2S low circuits

•	A malfunctioning HO2S

•	A problem in the HO2S heater or its circuit

•	A faulty HO2S ground

This DTC determines if the HO2S is functioning properly by checking for an adequate number of HO2S voltage transitions above and below the bias range of 300-600 mV. This DTC sets when the VCM fails to detect a minimum number of voltage transitions above and below the bias range during the test period. Possible causes of this DTC are listed below.

•	An open circuit or a short to voltage on either the HO2S signal or HO2S low circuits

•	A malfunctioning HO2S

•	A fault in the HO2S heater or its circuit

•	A poor HO2S ground

Conditions for Running the DTC

•	No active TP sensor DTCs

•	No active EVAP system DTCs

•	No active IAT sensor DTCs

•	No active MAP sensor DTCs

•	No active ECT sensor DTCs

•	No active MAF sensor DTCs

•	No active misfire DTCs

•	No intrusive tests (i.e., EGR or Catalyst) in progress

•	No device control active

•	The system voltage is more than 9 volts

•	The engine run time is more than 120 seconds

•	DFCO not active

•	The ECT is 80°C (176° F) or more

•	The MAF is 15 g/s or more

•	DTC P0141 not active

•	The system is in closed loop

Conditions for Setting the DTC

The O2 sensor voltage is between 394-473 mV for more than 100 seconds

Action Taken When the DTC Sets

•	The control module illuminates the malfunction indicator lamp (MIL) if a failure is detected during 2 consecutive key cycles.

•	The control module sets the DTC and records the operating conditions at the time the diagnostic failed. The failure information is stored in the scan tool Freeze Frame/Failure Records.

Conditions for Clearing the MIL or DTC

•	The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed.

•

A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle.

•	Use a scan tool in order to clear the DTCs.

Diagnostic Aids

Important: Never solder the HO2S wires. For proper wire and connection repairs, refer to Wiring Repairs or Connector Repairs in Wiring Systems.

Check for the following conditions:

Check for exhaust system leaks upstream of the suspect HO2S. The leak may be very small and typically be within 30.5 cm (12 in.) of the suspect HO2S. Refer to Exhaust System Inspection in Engine Exhaust.

A malfunctioning HO2S heater or heater circuit

With the ignition ON and the engine OFF, the HO2S voltage displayed on a scan tool should gradually drop to below 0.150 volt, indicating that the heater works properly. If not, disconnect the HO2S and connect a test lamp between the terminals C and D. If the test lamp does not light, repair the open in the HO2S ground circuit or the HO2S ignition positive voltage circuit. If the test lamp lights, replace the HO2S.

The Intermittent Test

Use a scan tool in order to monitor this HO2S signal voltage. Move the related connectors and the wiring harness with a warm engine running at part throttle in Closed Loop. If the failure is induced, the HO2S signal voltage reading changes from its normal fluctuating voltage (above 600 mV and below 300 mV) to a fixed value around 450 mV. This may help to isolate the location of the malfunction.

An intermittent may be caused by any of the following conditions:

•	A poor connection

•	Rubbed through wire insulation

•	A broken wire inside the insulation

Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.

If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step checks for proper sensor activity. When in Closed Loop fuel control the HO2S voltage should rapidly swing above and below the bias voltage.

This step checks the VCM and the HIGH and LOW circuits between the VCM and the HO2S connector for proper operation.

This step checks for proper HO2S heater circuit operation up to the HO2S connector.

This step checks for proper circuit resistance between the HO2S LOW circuit and VCM ground.

This step checks for proper circuit resistance between the HO2S LOW circuit and VCM ground with a COLD sensor. A loose HO2S or poor tread to exhaust electrical contact will cause higher resistance when the HO2S is cold. Although 500 ohms is allowed, typical resistance should be less than 50 ohms.

Step

Action

Value(s)

Yes

Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module's data is deleted once the Clear Info function is used.

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

Using a scan tool, store the DTC Information from the VCM into the scan tool.
Clear the DTC Information from the VCM.
Reset the Fuel Trim values.
Start and idle the engine until normal operating temperature is reached.
Using a scan tool monitor the HO2S voltage for the sensor that applies to this DTC.

Is the HO2S voltage fixed within the voltage range specified?

399-473 mV

Go to Step 4

Go to Step 3

This DTC is intermittent.

Are any additional DTCs stored?

Go to the applicable DTC table

Go to Diagnostic Aids

Turn OFF the ignition.
Disconnect the HO2S connector for the sensor that applies to this DTC.
Jumper the HO2S LOW circuit to a known good ground.
Jumper the HO2S HIGH signal circuit to a known good ground.
Turn ON the ignition leaving the engine OFF.
Using a scan tool monitor the HO2S voltage for the sensor that applies to this DTC.

Is the voltage less than the specified value?

20 mV

Go to Step 7

Go to Step 5

Turn OFF the ignition.
Remove the jumpers from the HO2S terminals.
Disconnect the VCM connector containing the HO2S HIGH and LOW circuits.
Using a J 39200 DMM measure the continuity of the HO2S HIGH signal circuit and then the HO2S LOW circuit between the VCM connector terminal and the HO2S connector terminal (engine harness side).

Is the resistance of both circuits less than the specified value?

5 ohms

Go to Step 6

Go to Step 9

Check for proper VCM connector terminal contact.
Repair as necessary. Refer to Connector Repairs in Wiring Systems.

Did you find a problem?

DTC P0140 HO2S Circuit Insufficient Activity Bank 1 Sensor 2 Under 8600 GVW without C6P

Circuit Description

Conditions for Running the DTC

Conditions for Setting the DTC

Action Taken When the DTC Sets

Conditions for Clearing the MIL or DTC

Diagnostic Aids

A malfunctioning HO2S heater or heater circuit

The Intermittent Test

Test Description

DTC P0140 HO2S Circuit Insufficient Activity Bank 1 Sensor 2 Over 8600 GVW with C6P

Circuit Description

Conditions for Running the DTC

Conditions for Setting the DTC

Action Taken When the DTC Sets

Conditions for Clearing the MIL or DTC

Diagnostic Aids

A malfunctioning HO2S heater or heater circuit

The Intermittent Test

Test Description