GM Service Manual Online
For 1990-2009 cars only

Removal Procedure


    Object Number: 310799  Size: SH
  1. Raise the hood to the service position, perform the following:
  2. • Remove the hood hinge bolts (1).
    • Raise the hood until vertical.
    • Install the hood hinge bolts until snug in the service position (2).
  3. Remove the radiator support. Refer to Radiator Support Replacement .
  4. Remove the front cover. Refer to Engine Front Cover Replacement .
  5. Remove the valve lifters. Refer to Valve Lifter Replacement .

  6. Object Number: 260128  Size: SH
  7. Remove the camshaft sensor bolt and sensor.

  8. Object Number: 156158  Size: SH
  9. Rotate the crankshaft until the timing marks on the crankshaft and camshaft sprockets are aligned.

  10. Object Number: 63263  Size: SH
  11. Remove the camshaft sprocket bolts.
  12. Notice: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.

  13. Remove the camshaft sprocket and reposition the timing chain.

  14. Object Number: 63211  Size: SH
  15. Remove the camshaft retainer bolts and retainer.
  16. Notice: All camshaft journals are the same diameter, so care must be used in removing or installing the camshaft to avoid damage to the camshaft bearings.


    Object Number: 63212  Size: SH
  17. Remove the camshaft.
  18. 10.1. Install 3 M8-1.25 x 100 mm (M8-1.25 x 4.0 in) bolts to the bolt holes in the front of the camshaft.
    10.2. Using the bolts as a handle, carefully rotate and pull the camshaft out of the engine block.
    10.3. Remove the 3 bolts from the camshaft.
  19. If required, clean and inspect the camshaft and bearings. Refer to Camshaft and Bearings Cleaning and Inspection .

Installation Procedure

Important: If camshaft replacement is required, the valve lifters must also be replaced.


    Object Number: 63212  Size: SH
  1. Lubricate the camshaft journals and the bearings with clean engine oil.
  2. Install 3 M8-1.25 x 100 mm (M8-1.25 x 4.0 in) bolts to the bolt holes in the front of the camshaft.
  3. Notice: All camshaft journals are the same diameter, so care must be used in removing or installing the camshaft to avoid damage to the camshaft bearings.

  4. Using the bolts as a handle, carefully install the camshaft into the engine block.
  5. Remove the 3 bolts from the front of the camshaft.

  6. Object Number: 63211  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Important: Install the retainer plate with the sealing gasket facing the engine block.

    The gasket surface on the engine block should be clean and free of dirt and/or debris.

  7. Install the camshaft retainer and bolts.
  8. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).


    Object Number: 63263  Size: SH
  9. Install the camshaft sprocket and position the timing chain.
  10. Install the camshaft sprocket bolts.
  11. Tighten
    Tighten the bolts to 35 N·m (26 lb ft).


    Object Number: 260128  Size: SH
  12. Inspect the camshaft sensor O-ring seal. If the O-ring seal is not cut or damaged, it may be reused.
  13. Lubricate the O-ring seal with clean engine oil.
  14. Install the camshaft sensor and bolt.
  15. Tighten
    Tighten the bolt to 25 N·m (18 lb ft).

  16. Install the valve lifters. Refer to Valve Lifter Replacement .
  17. Install the front cover. Refer to Engine Front Cover Replacement .
  18. Install the radiator support. Refer to Radiator Support Replacement .

  19. Object Number: 310799  Size: SH
  20. Remove the hood hinge bolts from the service position (2).
  21. Lower the hood to the normal position.
  22. Install the hood hinge bolts.
  23. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).