GM Service Manual Online
For 1990-2009 cars only

Circuit Description

When the ignition switch is turned ON, the rear wheel steering control module monitors communications between its internal microprocessors and performs self-diagnostic tests. If an internal malfunction is detected, the rear wheel steering control module will store a DTC C0550 in its memory.

Conditions for Running the DTC

Turn the ignition switch to the ON position, with engine ON.

Conditions for Setting the DTC

    • The rear wheel steering control module detected an internal malfunction.
    • The malfunction must be detected when the ignition switch is first turned ON.

Action Taken When the DTC Sets

    • The Service 4-Wheel Steer indicator in IPC will be displayed.
    • The code is displayed on scan the tool as DTC C0550.
    • The output command to the motor is zeroed. The motor drive circuits are disabled using commands from the rear wheel steering control module to open the power relay.
    • The rear wheels will be returned to the default centered position.

Conditions for Clearing the DTC

    • Conditions for the DTC are not currently present.
    • The module receives a clear code command from the scan tool.
    • The DTC clears after 100 malfunction free ignition cycles.

Diagnostic Aids

    • Any additional codes displayed with DTC C0550 should be diagnosed and repaired first.
    • The rear wheel steering control module tests for multiple internal malfunctions and will store a DTC C0550 if one or more internal malfunctions are detected. Therefore, depending on which malfunction was detected, and what internal circuitry was affected, this DTC may cause various symptoms.
    • Any condition resulting in the sensor supply voltage being pulled high or low could result in an erroneous DTC C0550.
    • A fault in the battery positive voltage circuit from the 125A MEGA fuse can result in an erroneous DTC C0550.

Step

Action

Values

Yes

No

Schematic Reference: Rear Wheel Steering Schematics

Connector End View Reference: Rear Wheel Steering Connector End Views

1

Did you perform the Diagnostic System Check-Rear Wheel Steering?

--

Go to Step 2

Go to Diagnostic System Check - Rear Wheel Steering

2

  1. Install a scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. With the scan tool, monitor the DTC information of the Rear Wheel Steering Control module.

Are there any additional codes displayed along with the DTC C0550?

--

Go to Diagnostic Trouble Code (DTC) List

Go to Step 3

3

With the scan tool, monitor the DTC information of the Rear Wheel Steering Control module.

Does the information indicate that the DTC C0550 is current?

--

Go to Step 4

Go to Diagnostic Aids

4

With the scan tool, observe the sensor supply voltage in the rear wheel steering data.

Is the voltage above the specified value?

5.0 V

Go to Step 7

Go to Step 5

5

With the scan tool, observe the sensor supply voltage in the rear wheel steering data.

Is the voltage below the specified value?

0.25 V

Go to Step 8

Go to Step 6

6

Test for an open or short to ground in the battery voltage supply circuit of the 125 A MEGA fuse. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 11

Go to Step 9

7

Test the 5-volt reference circuit for a short to battery voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 11

Go to Step 9

8

Test the 5-volt reference circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 11

Go to Step 9

9

Inspect for poor connections at the rear wheel steering control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 11

Go to Step 10

10

Important: Perform the learn alignment procedure. Refer to Wheel Alignment Measurement in Wheel Alignment.

Replace the rear wheel steering control module. Refer to Rear Wheel Steering Control Module Replacement in Rear Wheel Steering.

Did you complete the replacement?

--

Go to Step 11

--

11

  1. Use the scan tool to clear DTCs.
  2. Operate the vehicle within the conditions for running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK