Circuit Description
The PCM monitors the amount of vacuum/pressure in the EVAP system by monitoring the fuel tank pressure sensor signal. The PCM seals the EVAP system by commanding the EVAP Purge Solenoid OFF and the EVAP vent valve ON. The PCM monitors the fuel tank pressure sensor in order to determine if the EVAP Purge Solenoid is leaking vacuum to the EVAP system. This DTC sets if the vacuum in the EVAP system is greater than a predetermined value within a predetermined time.
Conditions for Running the DTC
| • | DTCs P0107, P0108, P0112, P0113, P0121, P0122, P0123, P0131-P0161, P0420, P0430, P0500, P0502, P0503, P0562, P0563, P1111, P1112, P1114, P1115, not set. |
| • | The ignition voltage is between 10.0 volts and 18.0 volts. |
| • | The barometric pressure is greater than 75 kPa. |
| • | The fuel level is between 15% and 85% of full capacity. |
| • | The engine coolant temperature is between 4°C (39°F) and 30°C (86°F). |
| • | The intake air temperature is between 4°C (39°F) and 30°C (86°F). |
| • | The start up engine coolant and intake air temperatures are within 9°C (16°F) of each other. |
| • | The TP angle is greater than 0% but less than 99.6%. |
Conditions for Setting the DTC
The EVAP system develops a vacuum greater than a predetermined value when purge is not commanded.
Action Taken When the DTC Sets
| • | The PCM illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The PCM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the PCM stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the PCM records the operating conditions at the time of the failure. The PCM writes the conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A last test failed, or current DTC, clears when the diagnostic runs and does not fail. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Use a scan tool in order to clear the MIL and the DTC. |
Diagnostic Aids
Important: Remove any debris from the PCM connector surfaces before servicing the PCM. Inspect the PCM connector gaskets when diagnosing/replacing the PCM. Ensure that the gaskets are installed correctly. The gaskets prevent water intrusion into the PCM.
Before replacing any components, visually/physically check for the following:
| • | Mis-routed harness. |
| • | Rubbed through wire insulation |
| • | Broken wire inside the insulation |
| • | Kinked or damaged vacuum hoses |
| • | Physically damaged system components |
| • | Inspect components and vacuum lines for traces of carbon or other contaminants. The presence of foreign material may be causing a restriction in the system or preventing the solenoid valve from closing properly. Either condition may cause a DTC to set. |
For an intermittent condition, refer to Symptoms .
Test Description
The numbers below refer to the step numbers on the Diagnostic Table.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||
Does the vacuum gauge indicate a vacuum? | -- | Go to Diagnostic Aids | ||
3 | Turn OFF the ignition. Important: Check for carbon contamination. Refer to Evaporative Emission System Cleaning . Replace the EVAP Purge Solenoid Valve. Refer to Evaporative Emission Canister Purge Solenoid Valve Replacement . Is the action complete? | -- | -- | |
4 |
Does the scan tool indicate that this test ran and passed? | -- | ||
5 | Select the Capture Info option and the Review Info option using the scan tool. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to the applicable DTC | System OK |
