GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 1998 🢒 GMC C Pickup - 2WD 🢒 General Information 🢒 Maintenance and Lubrication 🢒 Maintenance Schedule - Short Trip/City

Maintenance Schedule - Short Trip/City Gasoline

Perform the services shown in this schedule up to 166 000 km (100,000 miles) and after 166 000 km (100,000 miles) at the same intervals.

5 000 km (3,000 miles)

    • Change the engine oil and the filter every 5 000 km (3,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

10 000 km (6,000 miles)

    • Change the engine oil and the filter every 10 000 km (6,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

15 000 km (9,000 miles)

    • Change the engine oil and the filter every 15 000 km (9,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

20 000 km (12,000 miles)

    • Change the engine oil and the filter every 20 000 km (12,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

25 000 km (15,000 miles)

    • Change the engine oil and the filter every 25 000 km (15,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Inspect the air cleaner filter.
    • Clean the front wheel bearings (or each brake relining, whichever occurs first).
    • Repack the front wheel bearings (or each brake relining, whichever occurs first).
    • For vehicles with GVWR above 3 855 kg (8,500 lbs), inspect the following vehicle components for looseness:
       - The shields
       - The underhood insulation
    • Adjust or replace these components as specified.

30 000 km (18,000 miles)

    • Change the engine oil and the filter every 30 000 km (18,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

35 000 km (21,000 miles)

    • Change the engine oil and the filter every 35 000 km (21,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

40 000 km (24,000 miles)

    • Change the engine oil and the filter every 40 000 km (24,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

45 000 km (27,000 miles)

    • Change the engine oil and the filter every 40 000 km (27,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

50 000 km (30,000 miles)

    • Change the engine oil and the filter every 50 000 km (30,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Clean the front wheel bearings (or each brake relining, whichever occurs first).
    • Repack the front wheel bearing (or each brake relining, whichever occurs first).
    • Replace the air filter.
    • Replace the fuel filter. An Emission Control Service.
    • For vehicles with GVWR above 3 855 kg (8,500 lbs), inspect the following vehicle components for looseness:
       - The shields
       - The underhood insulation
    • Adjust or replace shields and the underhood insulation components as specified.
    • Inspect the hoses and the ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valve operates properly.
    • Rotate the tires. Refer to Tire Rotation in Suspension.
    • Inspect the shields and the underhood insulation.

55 000 km (33,000 miles)

    • Change the engine oil and the filter every 55 000 km (33,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

60 000 km (36,000 miles)

    • Change the engine oil and the filter every 60 000 km (36,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

65 000 km (39,000 miles)

    • Change the engine oil and the filter every 65 000 km (39,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

70 000 km (42,000 miles)

    • Change the engine oil and the filter every 70 000 km (42,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

75 000 km (45,000 miles)

    • Change the engine oil and the filter every 75 000 km (45,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Regularly inspect the air filter when driving in dusty conditions. Replace the air filter if necessary. An Emission Control Service *
    • Clean the front wheel bearings (or each brake relining, whichever occurs first).
    • Repack the front wheel bearing (or each brake relining, whichever occurs first).
    • For vehicles with GVWR above 3 855 kg (8,500 lbs), inspect the following vehicle components for looseness:
       - The shields
       - The underhood insulation
    • Adjust or replace shields and the underhood insulation components as specified.
    • Inspect the hoses and the ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valve operates properly.

80 000 km (48,000 miles)

    • Change the engine oil and the filter every 80 000 km (48,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

83 000 km (50,000 miles)

    • Change the automatic transmission fluid and the filter if the vehicle's GVWR exceeds 3 855 kg (8,600 lbs).
    • Change the automatic transmission fluid and the filter.

85 000 km (51,000 miles)

    • Change the engine oil and the filter every 85 000 km (51,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

90 000 km (54,000 miles)

    • Change the engine oil and the filter at 90 000 km (54,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

95 000 km (57,000 miles)

    • Change the engine oil and the filter at 95 000 km (57,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

100 000 km (60,000 miles)

    • Change the engine oil and the filter every 100 000 km (60,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Inspect the engine accessory drive belt. An Emission Control Service *
    • Replace the air filter.
    • Replace the fuel filter. An Emission Control Service *
    • Inspect the following fuel tank components for leaks or damages:
       - The fuel tank
       - The cap and lines
       - The fuel cap gasket
    • Replace the necessary damaged fuel tank components. An Emission Control Service *
    • Clean the front wheel bearings (or each brake relining, whichever occurs first).
    • Repack the front wheel bearing (or each brake relining, whichever occurs first).
    • For vehicles with GVWR above 3 855 kg (8,500 lbs), inspect the following vehicle components for looseness:
       - Shields
       - Underhood insulation
    • Adjust or replace shields and the underhood insulation components as specified.
    • Inspect the hoses and the ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valve operates properly.
    • Inspect the Evaporative Control System.
    • Verify the following components for proper routing and condition maintenance:
       - Fuel and vapor lines
       - Hoses
    • Verify that the purge valve operates properly if equipped. Replace as necessary.
    • Inspect the Control Exhaust Gas Recirculation (EGR) system.
    • Inspect the shields and the underhood insulation.

105 000 km (60,000 miles)

    • Change the engine oil and the filter every 105 000 km (63,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

110 000 km (66,000 miles)

    • Change the engine oil and the filter at 110 000 km (66,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

115 000 km (69,000 miles)

    • Change the engine oil and the filter every 115 000 km (69,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher. 
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

120 000 km (72,000 miles)

    • Change the engine oil and the filter at 120 000 km (72,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

125 000 km (75,000 miles)

    • Change the engine oil and the filter every 125 000 km (75,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Clean the front wheel bearings (or each brake relining, whichever occurs first).
    • Repack the front wheel bearings (or each brake relining, whichever occurs first).
    • For vehicles with GVWR above 3 855 kg (8,500 lbs), inspect the following vehicle components for looseness:
       - The shields
       - The underhood insulation
    • Adjust or replace shields and the underhood insulation components as specified.
    • Inspect the hoses and the ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valve operates properly.

130 000 km (78,000 miles)

    • Change the engine oil and the filter every 130 000 km (78,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

135 000 km (81,000 miles)

    • Change the engine oil and the filter every 135 000 km (81,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

140 000 km (84,000 miles)

    • Change the engine oil and the filter every 140 000 km (84,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

145 000 km (87,000 miles)

    • Change the engine oil and the filter every 145 000 km (87,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

150 000 km (90,000 miles)

    • Change the engine oil and the filter every 150 000 km (90,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Clean the front wheel bearings (or each brake relining, whichever occurs first).
    • Repack the front wheel bearing (or each brake relining, whichever occurs first).
    • For vehicles with GVWR above 3 855 kg (8,500 lbs), inspect the following vehicle components for looseness:
       - The shields
       - The underhood insulation
    • Adjust or replace shields and the underhood insulation components as specified.
    • Inspect the hoses and the ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valve operates properly.
    • Replace the air filter.
    • Replace the fuel filter. An Emission Control Service.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

155 000 km (93,000 miles)

    • Change the engine oil and the filter every 155 000 km (93,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

160 000 km (96,000 miles)

    • Change the engine oil and the filter every 160 000 km (96,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

165 000 km (99,000 miles)

    • Change the engine oil and the filter every 165 000 km (99,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
    • Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
    • Verify the rear fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

166 000 km (100,000 miles)

    • Inspect the engine timing.
    • Replace the spark plugs. An Emission Control Service *
    • Replace the spark plug wires. An Emission Control Service *
    • Change the automatic transmission fluid and the filter if the vehicle's GVWR exceeds 3 900 kg (8,600 lbs).
    • Change the automatic transmission fluid and the filter if the vehicle's GVWR exceeds 3 900 kg (8,600 lbs).
    • Change the automatic transmission fluid and the filter.
    • Inspect the Positive Crankcase Ventilation (PCV) Valve.

240 000 km (150,000 miles)

    • Drain, flush and refill the cooling system every 240 000 km (150,000 miles) or every 60 months, whichever occurs first.
    •  Refer to Fluid and Lubricant Recommendations .
    • Inspect the hoses.
    • Clean the radiator, condenser, pressure cap and the neck. An Emission Control Service *
    • Change the automatic transmission fluid and filter.

Maintenance Schedule - Short Trip/City Diesel

Perform the services shown in this schedule up to 240 000 km (150,000 miles) and after 240 000 km (150,000 miles) at the same intervals.

4 000 km (2,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        If three months pass before 4,000 km (2,500 miles), then change the oil after three months.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks.

8 000 km (5,000 miles )

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks.

12 000 km (7,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

16 000 km (10,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed and that the following components remain tight:
       - The hose connections
       - The fasteners
       - Other components
    • Inspect the air cleaner housing in order to ensure the following conditions:
       - The air cleaner housing seats properly.
       - The cover fits tightly.
       - The wing nuts are tight.
    • Tighten the connections and the fasteners or replace damaged components if necessary.

20 000 km (12,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks.

24 000 km (15,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the air cleaner filter.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks.
    • Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first)
    • Rotate the tires. Refer to Tire Rotation in Suspension.

28 000 km (17,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks.

32 000 km (20,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed and that the following components remain tight:
       - The hose connections
       - The fasteners
       - Other components
    • Inspect the air cleaner housing in order to ensure the following conditions:
       - The air cleaner housing seats properly.
       - The cover fits tightly.
       - The wing nuts are tight.
    • Tighten the connections and the fasteners or replace damaged components if necessary.

36 000 km (22,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Rotate the tires. Refer to Tire Rotation in Suspension.

40 000 km (25,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Replace the fuel cap.

44 000 km (27,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

48 000 km (30,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Replace the air filter. An Emission Control Service *
    • Replace the fuel filter.
    • Inspect the shields and the underhood insulation for looseness.
        Adjust or replace the shields and the underhood insulation if necessary.
    • Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first).
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed and that the following components remain tight:
       - The hose connections
       - The fasteners
       - Other components
    • Inspect the air cleaner housing in order to ensure the following conditions:
       - The air cleaner housing seats properly.
       - The cover fits tightly.
       - The wing nuts are tight.
    • Tighten the connections and the fasteners or replace damaged components if necessary.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

52 000 km (32,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

56 000 km (35,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is-12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

60 000 km (37,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Rotate the tires. Refer to Tire Rotation in Suspension.

64 000 km (40,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed and that the following components remain tight:
       - The hose connections
       - The fasteners
       - Other components
    • Inspect the air cleaner housing in order to ensure the following conditions:
       - The air cleaner housing seats properly.
       - The cover fits tightly.
       - The wing nuts are tight.
    • Tighten the connections and the fasteners or replace damaged components if necessary.
    • If the engine has a thermostatically controlled cooling fan, inspect the following components for proper hook-up:
       - All of the hoses
       - All of the ducts
       - If twelve months pass before the vehicle drives 40,000 miles, perform the above inspection procedure every twelve months.

68 000 km (42,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C  (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

72 000 km (45,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Inspect the air cleaner filter if the vehicle has been driven in dusty conditions.
        Replace the filter if necessary. An Emission Control Service *
    • Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first)
    • Rotate the tires. Refer to Tire Rotation in Suspension.

76 000 km (47,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

80 000 km (50,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Change the automatic transmission fluid and the filter if the vehicle's GVWR exceeds 3 900 kg (8,600 lbs) or if the vehicle is mainly driven under one or more of the following conditions:
       - In heavy traffic where the outside temperature regularly reaches 32°C (90°F) or higher.
       - In hilly or mountainous terrain.
       - When performing frequent trailer towing.
       - Uses such as found in the following services:
   • Taxi
   • Police
   • Delivery
    • Inspect the shields and the underhood insulation for looseness.
        Adjust or replace the shields and the underhood insulation as necessary.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed and that the following components remain tight:
       - Hose connections
       - Fasteners
       - Other components
    • Inspect the air cleaner housing in order to ensure the following conditions:
       - The air cleaner housing seats properly.
       - The cover fits tightly.
       - The wing nuts are tight.
    • Tighten the connections and the fasteners or replace damaged components if necessary.

84 000 km (52,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Rotate the tires. Refer to Tire Rotation in Suspension.

88 000 km (55,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

92 000 km (57,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

96 000 km (60,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Replace the air filter. An Emission Control Service *
    • Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first).
    • Inspect the crankcase depression regulator valve system for hoses exhibiting the following conditions:
       - Wear
       - Blockage
       - Collapse
       - An Emission Control Service *
    • Replace the fuel filter.
    • Inspect the crankcase depression regulator valve. An Emission Control Service *
    • Inspect the accessory drive (serpentine) belt for the following conditions:
       - Cracking
       - Fraying
       - Wear
       - Improper tension
       - Adjust or replace the belt as necessary.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed and that the following components remain tight:
       - The hose connections
       - The fasteners
       - Other components
    • Inspect the air cleaner housing in order to ensure the following conditions:
       - The air cleaner housing seats properly.
       - The cover fits tightly.
       - The wing nuts are tight.
    • Tighten the connections and the fasteners or replace damaged components if necessary.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

100 000 km (62,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

104 000 km (65,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

108 000 km (67,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Rotate the tires. Refer to Tire Rotation in Suspension.

112 000 km (70,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed and that the following components remain tight:
       - The hose connections
       - The fasteners
       - Other components
    • Inspect the air cleaner housing in order to ensure the following conditions:
       - The air cleaner housing seats properly.
       - The cover fits tightly.
       - The wing nuts are tight.
    • Tighten the connections and the fasteners or replace damaged components if necessary.
    • If the engine has a thermostatically controlled cooling fan, inspect the following components for proper hook-up:
       - All of the hoses
       - All of the ducts
       - If twelve months pass before the vehicle drives 64 000 km (40,000 miles) perform the above inspection procedure every twelve months.
    • Verify proper operation of the thermostatically controlled cooling fan valve.

116 000 km (72,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

120 000 km (75,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Inspect the air cleaner filter if the vehicle has been driven in dusty conditions.
        Replace the filter if necessary. An Emission Control Service *
    • If the vehicle is a 2 wheel drive vehicle, then clean and repack the front wheel bearings (or at each brake relining, whichever occurs first.)
    • Rotate the tires. Refer to Tire Rotation in Suspension.

124 000 km (77,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

128 000 km (80,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed and that the following components remain tight:
       - The hose connections
       - The fasteners
       - Other components
    • Inspect the air cleaner housing in order to ensure the following conditions:
       - The air cleaner housing seats properly.
       - The cover fits tightly.
       - The wing nuts are tight.
    • Tighten the connections and the fasteners or replace damaged components if necessary.
    • If the engine has a thermostatically controlled cooling fan, inspect the following components for proper hook-up:
       - All of the hoses
       - All of the ducts
       - If twelve months pass before the vehicle drives 64 000 km (40,000 miles), perform the above inspection procedure every twelve months.
    • Verify proper operation of the thermostatically controlled cooling fan valve.

132 000 km (82,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Rotate the tires. Refer to Tire Rotation in Suspension.

136 000 km (85,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

140 000 km (87,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

144 000 km (90,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Replace the air filter. An Emission Control Service *
    • Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first).
    • Replace the fuel filter.
    • Rotate the tires. Refer to Tire Rotation in Suspension.

148 000 km (92,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

152 000 km (95,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks

156 000 km (97,500 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drive 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Rotate the tires. Refer to Tire Rotation in Suspension.

160 000 km (100,000 miles)

    • Change the engine oil and the filter. An Emission Control Service *
        Change the engine oil and the filter as soon as one of the following conditions occurs:
       - Three months pass since the last oil change.
       - The vehicle drives 4 000 km (2,500 miles) since the last oil change.
    • Lubricate the following components:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The park brake cable guides
       - The brake pedal springs
       - The ball joints
       - Only lubricate the ball joints if the temperature of the ball joint is -12°C (10°F) or higher.
    • Inspect the rear fluid level.
        Add fluid if necessary.
    • Inspect the axle seals for leaks
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed and that the following components remain tight:
       - The hose connections
       - The fasteners
       - Other components
    • Inspect the air cleaner housing in order to ensure the following conditions:
       - The air cleaner housing seats properly.
       - The cover fits tightly.
       - The wing nuts are tight.
    • Tighten the connections and the fasteners or replace damaged components if necessary.
    • Inspect the hoses and replace the hoses if the hoses exhibit the following conditions:
       - Cracking
       - Swelling
       - Deterioration
    • Tighten all of the hose clamps (except the constant tension clamps).
    • Remove debris and clean the outside of the radiator and air conditioning condenser.
        Wash the radiator neck.
    • Pressure test the radiator and the cap in order to ensure proper operation.
    • Change the automatic transmission fluid and the filter.
    • If the engine has a thermostatically controlled cooling fan, inspect the following components for proper hook-up:
       - All of the hoses
       - All of the ducts
       - If twelve months pass before the vehicle drives 64 000 km (40,000 miles), perform the above inspection procedure every twelve months.
    • Verify proper operation of the thermostatically controlled cooling fan valve.

240 000 km (150,000 miles)

    • Drain, flush and refill the cooling system as soon as one of the following conditions occurs:
       - The vehicle reaches 240 000 km (150,000 miles).
       - Sixty months pass since the previous service
       - Refer to Recommended Fluid and Lubricants.
    • Inspect the hoses.
    • Clean the following components:
       - The radiator
       - The condenser
       - The pressure cap
       - The neck
       - An Emission Control Service *

Footnotes

The California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty. The California Air Resources Board has also determined that the failure to perform this maintenance item will not limit the recall liability prior to the completion of the vehicle useful life. GM, however, urges that all recommended maintenance be recorded.

Drive Axle Service:

    • The Locking Differential
        Drain the fluid and refill the fluid at the first engine oil change. At subsequent oil changes, inspect the fluid level and add fluid as necessary. Drain the fluid and refill the fluid every 25 000 km (15,000 miles) if the vehicle is performing either of the following actions:
       - Driving in dusty areas
       - Towing a trailer
    • The Standard Differential
        Inspect the fluid level and add fluid as necessary at every oil change. Drain the fluid and refill the fluid every 25 000 km (15,000 miles) if the vehicle is performing either of the following actions:
       - Driving in dusty areas
       - Towing a trailer
    • Heavy-duty or off-road use may require more frequent lubrication.