GM Service Manual Online
For 1990-2009 cars only

Object Number: 33140  Size: SF
Engine Controls Components
Engine Controls Schematics
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The VCM controls the idle speed with an Idle Air Control (IAC) valve to a calculated desired RPM based on the sensor inputs and the actual engine RPM. The VCM uses 4 circuits in order to move an Idle Air Control (IAC) valve, allowing a varying amount of air flow into the intake manifold.

In order to increase the idle RPM, the VCM moves the IAC valve out, allowing more air to bypass the throttle plate. In order to decrease the RPM, the VCM moves the IAC valve in, reducing the amount of air bypassing the throttle plate. A scan tool reads the VCM commands to the IAC valve in counts. The higher the counts, the more air is allowed to bypass the throttle plate (higher idle). The lower the counts, the less air that is allowed to bypass the throttle plates (lower idle). This DTC is a type B DTC.

Conditions For Setting DTC

Passive Test

    • No TP sensor DTCs set
    • No ECT DTCs set
    • No VSS DTCs set
    • No MAP DTCs set
    • ECT is greater than 72° C
    • IAT is greater than -25° C
    • BARO is graeter than 70 kPa (10,300 ft.)
    • Vehicle Speed is less than 2 mph
    • System voltage is between 10 volts and 18 volts
    • Engine run time is greater than 30 seconds.
    • TP is less than 1%
    • Above met for a time greater than 3 seconds
    • Change in Calculated Air flow is greater than 2 counts.

If the passive test fails, the active test is ran.

Active Test

    •  Calculated Air Flow is between 17.5 grams per second and 37.5 grams per second
    • Vehicle Speed is between 35 MPH and 85 MPH
    • Change in TP Sensor is less than 1%
    • Change in engine speed is less than 50 RPM
    • IAC motor commanded to 10% for 100 msec
    • Change in Calculated Air Flow is greater than 3 counts

Action Taken When the DTC Sets

The VCM will turn ON the MIL after 2 consecutive driving cycles with the fault active.

Conditions for Clearing the MIL/DTC

The VCM turns OFF the MIL after 3 consecutive driving trips without a fault condition present. A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles (the coolant temperature has risen 22°C (40°F) from the start-up coolant temperature and the engine coolant temperature exceeds 71°C (160°F) during that same ignition cycle) or the scan tool clearing feature has been used.

Diagnostic Aids

The following items could cause this DTC:

    • An IAC valve which is stopped and cannot respond to the VCM
    • A throttle stop screw which has been tampered with
    • A damaged throttle or linkage

A slow, unstable, or fast idle may be caused by a non - IAC valve system problem that cannot be overcome by the IAC valve. Out of range control IAC scan tool counts will read above 60 if the idle is too low and zero if the idle is too high. Check for the following:

    • Fuel system too lean and rich
    • Throttle body - inspect the bore for foreign material.
    • Refer to Rough, Unstable, or Incorrect Idle and Stalling .
    • IAC reset is done with the scan tool misc. functions mode.

Step

Action

Value(s)

Yes

No

1

Important: Before clearing DTCs, use the scan tool in order to record the freeze frame and the failure records for reference because the Clear Info function will lose the data.

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to A Powertrain On Board Diagnostic (OBD) System Check

2

Install the scan tool.

Are any other DTCs set?

--

Go to The Applicable DTC Table

Go to Step 3

3

Is the DTC P0506 active this ignition cycle?

--

Go to Step 5

Go to Step 4

4

This DTC is an intermittent. Refer to the Diagnostic Aids.

--

Go to Step 6

--

5

Problem is engine mechanical related. Refer to Engine Mechanical.

--

Go to Step 7

--

6

  1. Using the scan tool, select the DTC and the Clear Info.
  2. Start the Engine.
  3. Idle at the normal operating temperature.
  4. Select the DTC and the Specific.
  5. Enter the DTC number which was set.
  6. Operate the vehicle within the conditions for setting this DTC as specified in the supporting text.

Does the scan tool indicate that this diagnostic ran and passed?

--

Go to Step 7

Go to Step 2

7

Using the scan tool, select the Capture Info and the Review Info.

Are any DTCs displayed that have not been diagnosed?

--

Go to The Applicable DTC Table

System OK