GM Service Manual Online
For 1990-2009 cars only

DTC P0521 6.0L Engine

DTC Descriptor

DTC P0521: Engine Oil Pressure (EOP) Sensor Performance.

Diagnostic Fault Information

Always perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Engine Oil Pressure 5-Volts Reference Circuit

P0522

P0522

P0523

P0521

Engine Oil Pressure Sensor Signal Circuit

P0522

P0523

P0523

P0521

Low Reference

--

P0523

--

P0521

Circuit Description

The engine oil pressure (EOP) sensor changes resistance based on engine oil pressure. The engine control module (ECM) monitors the signal circuit of the EOP sensor. When the oil pressure is high, the sensor resistance is high, and the ECM senses a high signal voltage. When the oil pressure is low, the sensor resistance is low, and the ECM senses a low signal voltage. The ECM sends the engine oil pressure information to the instrument panel cluster (IPC) via the class 2 serial data circuit.

Conditions for Running the DTC

    • The engine is running with engine speed between 1000 and 3500 RPM.
    • Oil temperature is less than 140 C (284 F).

Conditions for Setting the DTC

The ECM does not detect a change in the engine oil pressure of at least 34.5 kPa (5 psi) over a predetermined variance of the engine speed.

Action Taken When the DTC Sets

    • The ECM records the operating conditions at the time the diagnostic test fails. The ECM displays this information in the Failure Records on the scan tool.
    • The IPC illuminates the engine oil pressure indicator.

Conditions for Clearing the DTC

    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The history DTC clears after 40 malfunction free warm-up cycles.
    • The ECM receives a clear code command from the scan tool.

Reference Information

Schematic Reference

    •  Instrument Cluster Schematics
    •  Engine Controls Schematics

Connector End View Reference

    •  Instrument Panel, Gages, and Console Connector End Views
    •  Engine Control Module Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Scan Tool Data List

Circuit/System Verification

With the scan tool installed and the engine idling, the Engine Oil Pressure Sensor parameter should indicate a range of 0.7-2.8 volts.

Circuit/System Testing

  1. Ignition ON, Engine ON, verify the scan tool Engine Oil Pressure Sensor parameter is within 0.7 V - 2.8 V.
  2. If not within the range of 0.7 V - 2.8 V, replace the EOP sensor.

Repair Instructions

Important: Always perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Engine Oil Pressure Sensor and/or Switch Replacement

DTC P0521 5.3L Engine

Diagnostic Instructions

Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

DTC Descriptor

DTC P0521: Engine Oil Pressure (EOP) Sensor Performance

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Engine Oil Pressure 5-Volts Reference Circuit

P0522

P0522

--

P0521

Engine Oil Pressure Sensor Signal Circuit

P0522

P0522

P0523

P0521

Low Reference

--

P0523

--

P0521

Circuit/System Description

The engine oil pressure (EOP) sensor changes voltage based on the engine oil pressure. The EOP sensor is a 3-wire sensor comprising of the signal circuit, the low reference circuit and the 5-volt reference circuit. The engine control module (ECM) supplies 5 volts to the EOP sensor via the 5-volt reference circuit and provides ground via the EOP low reference circuit. The ECM monitors the signal circuit of the EOP sensor to determine if the EOP sensor voltage is within the normal operating range of approximately 1-4 volts. When the engine oil pressure is high, the EOP sensor voltage is high and the ECM senses a high signal voltage. When the engine oil pressure is low, the EOP sensor voltage is low and the ECM senses a low signal voltage. The ECM sends the EOP information to the instrument panel cluster (IPC) via GMLAN serial data message. The ECM can also predict oil pressure as a function of engine speed and engine temperature.

Conditions for Running the DTC

    • The engine is running with engine speed between 700-3,500 RPM.
    • Oil temperature is less than 150°C (302°F).
    • Engine load stability is less than 250 kPa (36.2 psi).
    • Engine predicted pressure is between 50 kPa (7.3 psi) and 400 kPa (58 psi).
    • No crank sensor DTCs set.
    • No coolant sensor DTCs set.
    • No intake air temperature sensor DTCs set.
    • No MAF DTCs set.
    • No oil pressure sensor circuit DTCs set.

Conditions for Setting the DTC

The ECM detects that the difference between the predicted oil pressure and the actual oil pressure is either less than 47 kPa (6.8 psi) or greater than 50 kPa (7.3 psi).

Action Taken When the DTC Sets

    • The ECM records the operating conditions at the time the diagnostics test fails. The ECM displays this information in the Failure Records on the scan tool.
    • The IPC illuminates the EOP indicator.

Conditions for Clearing the DTC

    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The history DTC clears after 40 malfunction-free warm-up cycles.
    • The ECM receives a clear code command from the scan tool.

Reference Information

Schematic Reference

    •  Instrument Cluster Schematics
    •  Engine Controls Schematics

Connector End View Reference

    •  Instrument Panel, Gages, and Console Connector End Views
    •  Engine Control Module Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Scan Tool Data List for scan tool information

Circuit/System Verification

Engine ON, observe the Engine Oil Pressure Sensor parameter. The reading should be between 41-448 kPa (6-65 psi).

Circuit/System Testing

  1. Engine ON, transmission in park, vary the engine speed by 500 RPM.
  2. Verify the scan tool Engine Oil Pressure Sensor parameter changes by more than 34.5 kPa (5 psi).
  3. If less than 34.5 kPa (5 psi), refer to Oil Pressure Diagnosis and Testing .
  4. If the pressure tests normal, replace the EOP sensor.

Repair Instructions

Important: Always perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Engine Oil Pressure Sensor and/or Switch Replacement