GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2007 🢒 Canyon Pickup - 2WD 🢒 Diagnostic Navigation 🢒 Vehicle Diagnostic Information 🢒 Seat Belt Retractor Pretensioner Replacement - Front

Seat Belt Retractor Pretensioner Replacement - Front Crew Cab

Removal Procedure
  1. Disable the SIR system. Refer to SIR Disabling and Enabling .

    2. Object Number: 1276832 Size: SH
  2. Open the front seat belt upper guide shoulder bolt trim cover.
  3. Remove the front seat belt upper guide shoulder bolt.
  4. Remove the lower center pillar trim panel. Refer to Center Pillar Upper Trim Panel Replacement.
  5. Remove the front seat belt anchor bolt.
  6. Disconnect the electrical connector from the retractor/pretensioner.
  7. Remove the bolt that retains the seat belt retractor/pretensioner assembly to the body.
  8. Remove the front seat belt assembly from the vehicle.

Installation Procedure

    Object Number: 1276832 Size: SH
  1. Position the rear seat belt retractor/pretensioner assembly to the vehicle.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the bolt which retains the seat belt retractor/pretensioner assembly to the body.

    3. Tighten
    Tighten the seat belt retractor/pretensioner bolt to 52.5 N·m (39 lb ft).

  3. Connect the electrical connector to the retractor/pretensioner.
  4. Install the lower center pillar trim panel. Refer to Center Pillar Upper Trim Panel Replacement.
  5. Install the front seat belt anchor bolt. Ensure that the seat belt webbing is not twisted.

    6. Tighten
    Tighten the front seat belt anchor bolt to 52.5 N·m (39 lb ft).

  6. Install the front seat belt upper guide with the bolt. Ensure that the seat belt webbing is not twisted.

    7. Tighten
    Tighten the front seat belt upper guide bolt to 52.5 N·m (39 lb ft).

  7. Install the front seat belt upper guide shoulder bolt trim cover.
  8. Enable the SIR system. Refer to SIR Disabling and Enabling.

Seat Belt Retractor Pretensioner Replacement - Front Extended Cab

Removal Procedure
  1. Disable the SIR system. Refer to SIR Disabling and Enabling.

    2. Object Number: 1658649 Size: SH
  2. Open the belt upper guide shoulder bolt trim cover.
  3. Remove the front seat belt upper guide shoulder bolt.
  4. Remove the body rear corner trim panel. Refer to Body Side Rear Lower Trim Panel Replacement .
  5. Remove the seat belt anchor bolt.
  6. Disconnect the electrical connector from the retractor/pretensioner.
  7. Remove the bolt that retains the seat belt retractor/pretensioner assembly to the body.
  8. Remove the seat belt assembly from the vehicle.

Installation Procedure
  1. Position the seat belt retractor/pretensioner assembly to the vehicle.

    2. Object Number: 1658649 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the bolt which retains the seat belt retractor/pretensioner assembly to the body.

    3. Tighten
    Tighten the seat belt retractor/pretensioner bolt to 52.5 N·m (39 lb ft).

  3. Connect the electrical connector to the retractor/pretensioner.
  4. Install the seat belt upper guide with the bolt. Ensure that the seat belt webbing is not twisted.

    5. Tighten
    Tighten the seat belt upper guide bolt to 52.5 N·m (39 lb ft).

  5. Install the seat belt upper guide shoulder bolt trim cover.
  6. Install the seat belt anchor bolt. Ensure that the seat belt webbing is not twisted.

    7. Tighten
    Tighten the front seat belt anchor bolt to 52.5 N·m (39 lb ft).

  7. Install the body rear corner trim panel. Refer to Body Side Rear Lower Trim Panel Replacement .
  8. Enable the SIR system. Refer to SIR Disabling and Enabling.

Seat Belt Retractor Pretensioner Replacement - Front Regular Cab

Removal Procedure
  1. Disable the SIR system. Refer to SIR Disabling and Enabling .

    2. Object Number: 1276833 Size: SH
  2. Open the front seat belt upper guide shoulder bolt trim cover.
  3. Remove the front seat belt upper guide shoulder bolt.
  4. Remove the body rear corner trim panel. Refer to Body Side Rear Lower Trim Panel Replacement .

    5. Object Number: 1276834 Size: SH
  5. Remove the front seat belt anchor bolt.
  6. Disconnect the electrical connector from the retractor/pretensioner.
  7. Remove the bolt that retains the seat belt retractor/pretensioner assembly to the body.
  8. Remove the front seat belt assembly from the vehicle.

Installation Procedure
  1. Position the rear seat belt retractor/pretensioner assembly to the vehicle.

    2. Object Number: 1276833 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the bolt which retains the seat belt retractor/pretensioner assembly to the body.

    3. Tighten
    Tighten the seat belt retractor/pretensioner bolt to 52.5 N·m (39 lb ft).

  3. Connect the electrical connector to the retractor/pretensioner.
  4. Install the front seat belt upper guide with the bolt. Ensure that the seat belt webbing is not twisted.

    5. Tighten
    Tighten the front seat belt upper guide bolt to 52.5 N·m (39 lb ft).

  5. Install the front seat belt upper guide shoulder bolt trim cover.
  6. Install the body rear corner trim panel. Refer to Body Side Rear Lower Trim Panel Replacement .

    7. Object Number: 1276834 Size: SH
  7. Install the front seat belt anchor bolt. Ensure that the seat belt webbing is not twisted.

    8. Tighten
    Tighten the front seat belt anchor bolt to 52.5 N·m (39 lb ft).

  8. Enable the SIR system. Refer to SIR Disabling and Enabling .