Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B3265 00: Hatch Release Output CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Liftgate Relay Switch B+ | 2 | 2 | -- | -- |
Liftgate Release Switch Signal | B2494 00 | 1 | 1 | -- |
Liftgate Relay Coil Control | -- | 2 | B3265 00 | -- |
Liftgate Relay Coil Control Control | B2495 02 | 2 | B2495 01 | -- |
Liftgate Latch Control | -- | 2 | 2 | -- |
Liftgate Latch Ground | -- | 2 | 2 | -- |
Liftgate Switch Ground | -- | 1 | 1 | -- |
1. Liftgate Release Switch Malfunction 2. Liftgate Release Malfunction | ||||
Circuit/System Description
The body control module (BCM) provides voltage to the liftgate release relay control circuit thus energizing the L/GATE relay which provides voltage to the liftgate latch assembly releasing the liftgate.
Conditions for Running the DTC
The system voltage is 9-16 volts.
Conditions for Setting the DTC
The BCM detects short to voltage in the liftgate latch relay coil control ground circuit.
Action Taken When the DTC Sets
The liftgate latch will malfunction.
Conditions for Clearing the DTC
| • | The DTC will be current for as long as the fault is present. |
| • | When the fault is no longer present, the DTC will be a history DTC. |
| • | A history DTC will clear after 50 ignition cycles. |
Diagnostic Aids
Before testing can be performed the liftgate must be opened. Refer to Opening the Liftgate Without Electrical Power for the appropriate procedure.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Rear Hatch/Gate Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Command the liftgate latch to release by pressing the exterior liftgate control switch. The liftgate latch assembly should release the liftgate.
Circuit/System Testing
- Ignition OFF, disconnect the L/GATE relay.
- Connect a test lamp between the control circuit terminal 86 and B+.
- Command the liftgate latch assembly by pressing and releasing the exterior liftgate control switch. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, test or replace the L/GATE relay.
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always ON, test the liftgate relay high circuit for a short to ground. If the circuit tests normal, replace the BCM. |
Component Testing
- Ignition OFF, disconnect the L/GATE relay.
- Test for 60-200 ohms between terminals 85 and 86.
- Test for infinite resistance between the following terminals:
- Install a 3A fused jumper wire between the relay terminal 85 and 12V. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms between terminals 30 and 87.
| ⇒ | If not within the specified range, replace the relay. |
| • | 30 and 86 |
| • | 30 and 87 |
| • | 30 and 85 |
| • | 85 and 87 |
| ⇒ | If less than the specified range, replace the L/GATE relay. |
| ⇒ | If greater than the specified range, replace the L/GATE relay. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, setup and programming |
