GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B1580: Mirror Horizontal Position Sensor Circuit

DTC B1590: Mirror Vertical Position Sensor Circuit

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

5-Volt Reference

B1580, B1590

B1580, B1590

B1580, B1590

--

Driver/Passenger Mirror Horizontal Position Sensor Signal

B1580

B1580

B1580

--

Driver/Passenger Mirror Vertical Position Sensor Signal

B1590

B1590

B1590

--

Low Reference

B1580, B1590

B1580, B1590

B1580, B1590

--

Circuit/System Description

The Driver Door Switch (DDS) and Passenger Door Switch (PDS) determine the position of the outside rearview mirrors based on inputs from two mirror position sensors, one for vertical position, the other for horizontal position. 5 volts is applied to each sensor through a shared 5-volt reference circuit and a shared low reference circuit supplies ground. Each sensor has an individual signal circuit which provides position voltage to the DDS/PDS.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

B1580

An improper voltage level is seen on the horizontal position sensor signal circuit.

B1590

An improper voltage level is seen the vertical position sensor signal circuit.

Action Taken When the DTC Sets

Mirror movement is suspended so long as the fault is present.

Conditions for Clearing the DTC

    • A current DTC will clear when the fault is no longer present.
    • A history DTC will clear after 40 malfunction-free ignition cycles.

Reference Information

Schematic Reference

Outside Rearview Mirror Schematics

Connector End View Reference

Mirror Connector End Views

Description and Operation

Outside Mirror Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions

Circuit/System Verification

Ignition ON, observe the scan tool Mirror Horizontal Position and Mirror Vertical Position parameters. The reading should be between 0.2-4.8 volts and change as the mirror is moved, left, right, up, and down.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector X1 at the appropriate outside rearview mirror.
  2. Ignition OFF, test for less than 1.0 ohm of resistance between the low reference circuit terminal 10 and ground.
  3. If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the appropriate door switch.
  4. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 7 and ground.
  5. If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the appropriate door switch.
    If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the appropriate door switch.
  6. Install a 3A fused jumper wire between the signal circuit terminal 4 and the low reference circuit terminal 10. Verify the scan tool Mirror Vertical Position parameter is less than 0.2 volt.
  7. If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the appropriate door switch.
  8. Install a 3A fused jumper wire between the signal circuit terminal 5 and the low reference circuit terminal 10. Verify the scan tool Mirror Horizontal Position parameter is less than 0.2 volt.
  9. If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the appropriate door switch.
  10. Install a 3A fused jumper wire between the signal circuit terminal 4 and the 5-volt reference circuit terminal 7. Verify the scan tool Mirror Vertical Position parameter is greater than 4.8 volts.
  11. If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the appropriate door switch.
  12. Install a 3A fused jumper wire between the signal circuit terminal 5 and the 5-volt reference circuit terminal 7. Verify the scan tool Mirror Horizontal Position parameter is greater than 4.8 volts.
  13. If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the appropriate door switch.
  14. If all circuits test normal, test or replace the appropriate outside rearview mirror motor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Outside Rearview Mirror Motor Replacement
    •  Control Module References for DDS or PDS replacement, setup, and programming