Diagnostic Instructions

DTC Descriptor

DTC P0010 00:  Intake Camshaft Position Actuator Solenoid Control Circuit

DTC P0013 00:  Exhaust Camshaft Position Actuator Solenoid Control Circuit

DTC P2088 00:  Intake Camshaft Position Actuator Solenoid Control Circuit Low Voltage

DTC P2089 00:  Intake Camshaft Position Actuator Solenoid Control Circuit High Voltage

DTC P2090 00:  Exhaust Camshaft Position Actuator Solenoid Control Circuit Low Voltage

DTC P2091 00:  Exhaust Camshaft Position Actuator Solenoid Control Circuit High Voltage

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
Intake Camshaft Position Actuator Solenoid Control	P2088 00	P0010 00	P2089 00	P000A 00
Intake Camshaft Position Actuator Supply Voltage	--	P0010 00	--	--
Exhaust Camshaft Position Actuator Solenoid Control	P2090 00	P0013 00	P2091 00	P000B 00, P0014 00
Exhaust Camshaft Position Actuator Supply Voltage	--	P0013 00	--	--

Circuit/System Description

The camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust system enables the engine control module (ECM) to change the timing of the camshafts while the engine is operating. The camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid signal from the ECM is pulse width modulated (PWM). The ECM controls the camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid duty cycle by controlling the amount of solenoid ON time. The camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid controls the advance or the retard of each camshaft. The camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid controls the oil flow that applies the pressure to advance or retard the camshafts.

Ignition voltage is supplied directly to the camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid. The ECM controls the camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid by grounding the control circuit with a solid state device called a driver. The driver is equipped with a feedback circuit that is pulled-up to a voltage. The ECM can determine if the control circuit is open, shorted to ground, or shorted to a voltage by monitoring the feedback voltage.

Conditions for Running the DTC

Conditions for Setting the DTC

P0010 00

The ECM detects an open in the camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid circuits for greater than 1 s or a cumulative of 5 s when the solenoid is commanded OFF.

P0013 00

The ECM detects an open in the camshaft position actuator solenoid valve - exhaust solenoid circuits for greater than 1 s or a cumulative of 5 s when the solenoid is commanded OFF.

P2088 00

The ECM detects a short to ground in the camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid circuits for greater than 1 s or a cumulative of 5 s, when the solenoid is commanded OFF.

P2089 00

The ECM detects a short to voltage in the camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid circuits for greater than 1 s or a cumulative of 5 s, when the solenoid is commanded ON.

P2090 00

The ECM detects a short to ground in the camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust Solenoid circuits for greater than 1 s or a cumulative of 5 s, when the solenoid is commanded OFF.

P2091 00

The ECM detects a short to voltage in the camshaft position actuator solenoid valve - intake and camshaft position actuator solenoid valve - exhaust solenoid circuits for greater than 1 s or a cumulative of 5 s, when the solenoid is commanded ON.

Action Taken When the DTC Sets

DTCs P0010 00, P0013 00, P2088 00, P2089 00, P2090 00, P2090 01 are type B DTCs.

Conditions for Clearing the DTC

DTCs P0010 00, P0013 00, P2088 00, P2089 00, P2090 00, P2091 00 are type B DTCs.

Diagnostic Aids

If the condition is intermittent, move the related harnesses and connectors, with the engine operating, while monitoring the scan tool circuit status parameters for the component. The circuit status parameters change from OK or not run to fault if there is a condition with the circuit or a connection.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

1. With the engine at normal operating temperature, raise the engine speed to 2000 RPM for 10 s. DTCs P0010 00, P0013 00, P2088 00, P2098 00, P2090 00, and P2091 00 should not set.
2. Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the freeze frame/failure records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust.
2. Ignition ON, verify that a test lamp illuminates between the appropriate Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust ignition circuit terminal 1 and ground.

⇒	If the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

3. Connect a DMM, set on the diode setting, between the Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust control circuit terminal 2 and ground. The voltage should be greater than 2.0 V.

⇒

If the DMM displays OL, test the control circuit terminal 2 of the Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust for a short to voltage or an open/high resistance. If the circuit/connections test normal, replace the K20 Engine Control Module (ECM).

⇒

If less than the specified value, test the control circuit terminal 2 of the Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust for a short to ground. If the circuit tests normal, replace the K20 Engine Control Module (ECM).

4. Command the Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust CMP actuator solenoid ON and OFF with a scan tool. The DMM should transition from greater than 2 V when commanded OFF to less than 1 V, when commanded ON.

⇒	If the circuit voltage does not correspond to the specified values, replace the K20 Engine Control Module (ECM).

5. If all circuits/connections test normal, test or replace the Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust CMP actuator solenoid.

Component Testing

Static Test

1. Test for 7-12 Ω between the terminals of the Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust CMP actuator solenoid.

⇒	If not within the specified range, replace the Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust CMP actuator solenoid.

2. Test for greater than 500 MΩ between each terminal of the Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust CMP actuator solenoid and the CMP actuator solenoid housing.

⇒	If less than the specified value, replace the Q6F Camshaft Position (CMP) Actuator Solenoid Valve - Intake or the Q6E Camshaft Position (CMP) Actuator Solenoid Valve - Exhaust CMP actuator solenoid valve.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.