Ignition Lock Cylinder Replacement Cylinder Rotates

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

Caution: Refer to SIR Caution in the Preface section.

2. Disable the SIR system. Refer to SIR Disabling and Enabling in SIR.
3. Remove the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
4. Remove the steering wheel. Refer to Steering Wheel Replacement .
5. Remove the tilt lever.
6. Remove only the steering column LOWER trim cover. Refer to Steering Column Trim Covers Replacement .
7. Remove only the steering column upper shroud fasteners.



8. Lift the upper steering column shroud in order to gain access to the lock cylinder access hole (1).
9. Insert the bent tip awl into the ignition lock cylinder access hole (1).



10. Turn the ignition lock cylinder to START.



11. Use the bent tip awl in order to push down on the ignition lock cylinder retainer.
12. Release the ignition lock cylinder to RUN.



13. Remove the ignition lock cylinder from the ignition lock cylinder case.

1. Insert the ignition lock cylinder through the upper shroud.
2. Align the lock cylinder retaining tab and the position tab with the slots in the lock housing.
3. Push the lock cylinder into the ignition lock cylinder case completely.
4. Install the LOWER trim cover. Refer to Steering Column Trim Covers Replacement .
5. Install the tilt wheel lever.
6. Install the steering wheel. Refer to Steering Wheel Replacement .
7. Install the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
8. Enable the SIR system. Refer to SIR Disabling and Enabling in SIR.
9. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

Ignition Lock Cylinder Replacement Unable to Rotate Cylinder

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

Caution: Refer to SIR Caution in the Preface section.

2. Disable the SIR system. Refer to SIR Disabling and Enabling in SIR.
3. Remove the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
4. Remove the steering wheel. Refer to Steering Wheel Replacement .
5. Remove the tilt lever.
6. Remove ONLY the steering column LOWER trim cover. Refer to Steering Column Trim Covers Replacement .
7. Remove the SIR coil. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in SIR.
8. Remove the shaft lock shield and the turn signal cancel cam. Refer to Turn Signal Cancel Cam and Steering Shaft Upper Bearing Spring Replacement .
9. Remove only the steering column upper trim cover fasteners.
10. Remove the park lock cable from the ignition lock cylinder case.

Important: The lock bolt has spring tension from the lock bolt spring. Hold the lock bolt while you remove the ignition lock cylinder case.

11. Remove the ignition lock cylinder case with the ignition switch, the theft deterrent module and the steering column upper trim cover. Refer to Ignition Lock Cylinder Case Replacement .



12. Remove the ignition lock cylinder case rear cover in order to gain access to the ignition lock cylinder case sector gears.

Important: Make a mark (1) on both of the ignition lock cylinder case sector gears in order to ensure proper sector gear timing after the ignition lock cylinder case is assembled.

13. Remove the ignition lock cylinder case sector gears.



14. Use a small burring tool in order to carefully remove the lock cylinder position tab.
15. Use a small flat-bladed tool in order to press and hold the lock cylinder retainer (1).
16. Remove the lock cylinder from the ignition lock cylinder case.
17. Remove all of the metal shavings from the ignition lock cylinder case.



18. Record the lock cylinder four-character key code (1) on the lock cylinder.
19. Cut a new key according to the four-character lock cylinder key code. Refer to Key and Lock Cylinder Coding in General Information.
20. Ensure that the new ignition key operates in all of the vehicle lock cylinders.
21. Code the NEW ignition lock cylinder according to the four-character lock cylinder key code. Refer to Key and Lock Cylinder Coding in General Information.

1. Align the marks (1) on the ignition lock cylinder case sector gears and install the sector gears.
2. Ensure that the ignition lock cylinder case is in the OFF/LOCK position.
3. Insert the ignition key into the NEW ignition lock cylinder.
4. Align the lock cylinder retaining tab and the position tab with the slots in the lock housing.
5. Push the lock cylinder into the lock housing completely.
6. Rotate the lock cylinder to ACC.
7. Ensure that the sector gear arrows point toward each other. If the sector gear arrows do not point toward each other, remove the sector gears and install the sector gears properly.
8. Install ignition lock cylinder case rear cover.
9. Push the lock bolt completely into the into the tilt head and hold the lock bolt.
10. Install the ignition lock cylinder case with the ignition switch, the theft deterrent module and the steering column upper trim cover. Refer to Ignition Lock Cylinder Case Replacement .
11. Install the park lock cable to the ignition lock cylinder case.
12. Adjust the park lock cable.
13. Install the steering column lower trim cover. Refer to Steering Column Trim Covers Replacement .
14. Install the turn signal cancel cam and the shaft lock shield. Refer to Turn Signal Cancel Cam and Steering Shaft Upper Bearing Spring Replacement .
15. Install the SIR coil. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in SIR.
16. Install the steering wheel. Refer to Steering Wheel Replacement .
17. Install the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
18. Enable the SIR system. Refer to SIR Disabling and Enabling in SIR.
19. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.