Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B3855: Rollover Sensor PerformanceDTC B3856: Discard Rollover Sensor
DTC B3857: Incorrect Rollover Sensor Installed
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Rollover Sensor Ignition | B3855 | B3855 | -- | -- |
Rollover Sensor Serial Data Link | B3855 | B3855 | B3855 | B3855 |
Rollover Sensor Ground | -- | B3855 | B3855 | -- |
Circuit/System Description
The inflatable restraint vehicle rollover sensor utilizes battery power supply and a bidirectional interface circuit. The rollover sensor modulates current on the interface to send ID, State of Health, and deployment commands to the inflatable restraint sensing and diagnostic module (SDM). When the ignition is turned on the rollover sensor responds by performing internal diagnostics and sending an ID to the SDM. The rollover sensor continually communicates status messages to the SDM, which determines if a fault is present in the rollover sensor circuit.
Conditions for Running the DTC
Ignition voltage is between 9-16 volts.
Conditions for Setting the DTC
B3855
| • | A valid ID message is not received within 5 seconds of the rollover sensor being powered up. |
| • | A status message is not received. |
B3856
| • | The SDM has received a NOK message from the rollover sensor. |
| • | A ROS internal fault exists for a 127 ignition cycles. |
B3857
When the SDM has received an ID message from the rollover sensor that does not match the ID stored in the SDM memory.
Action Taken When the DTC Sets
The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.
Conditions for Clearing the DTC
| • | The DTC will clear when the condition responsible for setting the DTC no longer exists. |
| • | A history DTC will clear once 250 malfunction-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
SIR System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition ON, if B3856 or B3857 is current, replace the rollover sensor.
- Ignition OFF, disconnect the harness connector at the rollover sensor and the SDM.
- Test for less than 1.0 ohm between the ground circuit terminal 6 and ground.
- Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.
- Test for less than 1 volt between the serial data circuit terminal 5 and ground.
- Ignition OFF, test for infinite resistance between the serial data circuit terminal 5 and ground.
- Test for less than 1 ohm between the rollover sensor terminal 5 and SDM terminal 35.
- If all circuits test normal, replace the rollover sensor.
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. |
| ⇒ | If greater than the specified range, test the serial data circuit for a short to voltage. |
| ⇒ | If less than the specified value, test the serial data circuit for a short to ground. |
| ⇒ | If less than the specified value, test the serial data link for an open/high resistance. |
| ⇒ | If the DTC resets as current, replace the SDM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for SDM replacement, setup, and programming |
