GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B0174: Output Air Temperature Sensor 1 Circuit Range/Performance

DTC B0179: Output Air Temperature Sensor 2 Circuit Range/Performance

DTC B0510: Output Air Temperature Sensor 3 Circuit Range/Performance

DTC B0515: Output Air Temperature Sensor 4 Circuit Range/Performance

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Upper Left Air Temperature Sensor Signal

B0174

B0174

B0174

--

Upper Right Air Temperature Sensor Signal

B0510

B0510

B0510

--

Lower Left Air Temperature Sensor Signal

B0179

B0179

B0179

--

Lower Right Air Temperature Sensor Signal

B0515

B0515

B0515

--

Low Reference

--

B0174, B0510, B0179, B0515,

B0174, B0510, B0179, B0515,

--

Circuit/System Description

The HVAC control module supplies the air duct temperature sensors with a low reference circuit and 5-volt signal circuit. The HVAC control module determines the voltage drop across the sensor, which is proportional to temperature. As the air temperature increases, the sensor resistance decreases and the voltage signal decreases. As the air temperature decreases, the sensor resistance increases and the voltage signal increases.

    • Output Air Temperature Sensor 1 refers to the upper left air duct temperature sensor
    • Output Air Temperature Sensor 2 refers to the lower left air duct temperature sensor
    • Output Air Temperature Sensor 3 refers to the upper right air duct temperature sensor
    • Output Air Temperature Sensor 4 refers to the lower right air duct temperature sensor

Conditions for Running the DTC

The ignition is turned ON.

Conditions for Setting the DTC

The HVAC control module detects the air temperature sensor signal circuit is less than -36°C (-38°F) or greater than 215°C (419°F) for greater than 15 seconds.

Action Taken When the DTC Sets

The system operates using a default value.

Conditions for Clearing the DTC

    • The DTC will become history if the HVAC control module no longer detects the condition that set the DTC.
    • The history DTC will clear after 50 fault-free ignition cycles.

Reference Information

Schematic Reference

HVAC Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

    •  Air Temperature Description and Operation
    •  Air Delivery Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Ignition ON, observe the appropriate scan tool air duct temperature sensor. The reading should be between -35°C (-39°F) and 98°C (208°F) and change with duct air temperature changes.

Circuit/System Testing

Important: If an air duct temperature sensor has an out of range condition caused by a short to voltage, short to ground, or an open/high resistance, the scan tool will display the same value: 39°F (4°C).

  1. Ignition OFF, disconnect the harness connector at the appropriate air duct temperature sensor.
  2. Ignition OFF, test for less than 10 ohms between the low reference circuit terminal 2 and ground.
  3. If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the HVAC control module.
  4. Ignition ON, test for 4.8-5.2 volts between the low reference circuit terminal 2 and the signal circuit terminal 1.
  5. If less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the HVAC control module.
    If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HVAC control module.
  6. If all circuits test normal, test or replace the air duct temperature sensor.

Component Testing

  1. Test the air duct temperature sensor by varying the sensor temperature while monitoring the sensor resistance.
  2. Compare the readings with the Temperature VS Resistance table Sensor Resistance Table and verify that the resistance is within 5 percent of the specification.
  3. If not within the specified range, replace the sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Duct Air Temperature Sensor Replacement - Upper Right Side
    •  Duct Air Temperature Sensor Replacement - Upper Left Side
    •  Duct Air Temperature Sensor Replacement - Lower Left Side
    •  Duct Air Temperature Sensor Replacement - Lower Right Side
    •  Control Module References for HVAC control module replacement, setup and programming