Diagnostic Instructions

DTC Descriptors

DTC B0012: Passenger Frontal Deployment Loop (Stage 2) Resistance Low

DTC B0013: Passenger Frontal Deployment Loop (Stage 2) Open

DTC B0014: Passenger Frontal Deployment Loop (Stage 2) Voltage Out of Range

DTC B0016: Passenger Frontal Deployment Loop (Stage 1) Resistance Low

DTC B0017: Passenger Frontal Deployment Loop (Stage 1) Open

DTC B0018: Passenger Frontal Deployment Loop (Stage 1) Voltage Out of Range

Diagnostic Fault Information

Circuit	Short to Ground	High Resistance	Open	Short to Voltage	Signal Performance
I/P Module Stage 1 High	B0018	B0018	B0017	B0018	B0016
I/P Module Stage 1 Low	B0018	B0018	B0017	B0018	B0016
I/P Module Stage 2 High	B0014	B0014	B0013	B0014	B0012
I/P Module Stage 2 Low	B0014	B0014	B0013	B0014	B0012

Circuit/System Description

During a side or frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the instrument panel (I/P) module. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. There are 2 shorting bars used within the I/P module connector which will short together both I/P module stage 1 high and low circuits, and both I/P module stage 2 high and low circuits, when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0012 Stage 2 or B0016 Stage 1

The I/P module deployment loop resistance is less than 1.3 ohms for 500 milliseconds.

B0013 Stage 2 or B0017 Stage 1

B0014 Stage 2 or B0018 Stage 1

Action Taken When the DTC Sets

Conditions for Clearing the DTC

Diagnostic Aids

If there is more than one DTC set diagnose the open DTC first.

Reference Information

Schematic Reference

SIR Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

SIR System Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information.

Special Tools

Circuit/System Testing

Important: When removing the connectors inspect for damage or corrosion. Damage or corrosion to the following requires repair or replacement of the affected component/connector:

•	SDM module

•	I/P wiring harness connector

•	SDM wiring harness connector

Important: The connector and connector position assurance (CPA) may seat independent of each other. Both the connector and CPA should seat with an audible and/or tactile click. The CPA isolates the shorting-bars within the connector allowing the deployment circuit to operate properly.

1. Verify that the I/P module connector and the CPA are engaged.

⇒	If the above condition is not found, make the appropriate repair.

2. Ignition OFF, disconnect harness connector at I/P inflatable restraint module.
3. Use J 38715-80 to connect the J 38715-A in place of the inflatable restraint module. Use the PASSENGER INFLATOR and BASE of COLUMN connectors located on the load tool.
4. Ignition ON, use a scan tool to observe the SIR DTC display. Verify DTC B0012, B0013, B0014, B0016, B0017, or B0018 is current.

⇒

If DTC B0012, B0013, B0014, B0016, B0017, or B0018 is not set or set as history, cycle ignition OFF, disconnect the adapter and J 38715-A , reconnect the harness connector at the I/P inflatable restraint module, and cycle the ignition ON. If the DTC resets after reconnecting the module, replace the I/P inflatable restraint module.

5. Ignition OFF, disconnect and remove the J 38715-A and adapter.
6. Disconnect the SDM harness connector.
7. Ignition ON, test for less than 1 volt between the appropriate high control circuit listed below and ground:

•	Stage 1 SDM terminal 6

•	Stage 2 SDM terminal 10

⇒	If greater than the specified range, test the control circuit for a short to voltage.

8. Test for less than 1 volt between the appropriate low control circuit terminal listed below and ground:

•	Stage 1 SDM terminal 7

•	Stage SDM 2 terminal 11

⇒	If greater than the specified range, test the control circuit for a short to voltage.

9. Ignition OFF, test for infinite resistance between the appropriate high control circuit terminal listed below and ground:

•	Stage 1 SDM terminal 6

•	Stage 2 SDM terminal 10

⇒	If less than the specified value, test the control circuit for a short to ground.

10. Test for infinite resistance between the appropriate low control circuit terminal listed below and ground:

•	Stage 1 SDM terminal 7

•	Stage 2 SDM terminal 11

⇒	If less than the specified value, test the control circuit for a short to ground.

11. Test for less then 1 ohm between the appropriate high control circuit terminals listed below:

•	Stage 1 SDM terminal 6 and the I/P module terminal  A1

•	Stage 2 SDM terminal 10 and the I/P module B1

⇒	If greater than the specified range, test the control circuit for an open/high resistance.

12. Test for less then 1 ohm between the appropriate low control circuit terminals listed below:

•	Stage 1 SDM terminal 7 and the I/P module terminal  A2

•	Stage 2 SDM terminal 11 and the I/P module B2

⇒	If greater than the specified range, test the control circuit for an open/high resistance.

13. If all circuits test normal, replace the SDM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.