DTC C1261 Right Front ABS Motor Circuit Open. Chevrolet Tracker

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 1998 🢒 Tracker - 2WD 🢒 DTC 🢒 DTC C1261 Right Front ABS Motor Circuit Open

ABS Components
Antilock Brake System Schematics

Circuit Description

DTC C1261 identifies an ABS motor that cannot energize due to an open in the ABS motor circuitry. The malfunction will not allow proper front ABS operation.

Conditions for Setting the DTC

•	DTC C1261 can only set when the motor is commanded off.

•	A malfunction exists if the EBCM detects an out of range voltage on either of the right front ABS motor circuits. The out of range voltage on either circuit indicates an open circuit exists.

Action Taken When the DTC Sets

•	An open ABS motor will not activate.

•	A malfunction DTC stores.

•	The ABS disables.

•	The ABS warning indicator turns ON.

Conditions for Clearing the DTC

•	The condition responsible for setting the DTC no longer exists and the Scan Tool Clear DTCs function is used.

•	100 drive cycles pass with no DTCs detected. A drive cycle consists of starting the vehicle, driving the vehicle over 16 km/h (10 mph), stopping and then turning the ignition off.

Diagnostic Aids

Use the Scan Tool Manual Control function in order to exercise ABS motor movement of affected channel in both directions while applying light pressure on the brake pedal.

An intermittent malfunction may be indicated if erratic or jumpy brake pedal movement is detected while performing an apply or release function of the ABS monitor.

The following conditions may cause an intermittent malfunction:

•	A poor connection

•	Rubbed-through wire insulation

•	A broken wire inside the insulation

If the malfunction is not current, use the following procedure to pinpoint an intermittent malfunction in the motor circuitry or connections:

Wiggle the wires of the affected channel.
Inspect if the DTC resets.

Use the enhanced diagnostic function of the Scan Tool in order to measure the frequency of the malfunction.

Thoroughly inspect any circuitry that may be causing the intermittent complaint for the following conditions:

•	Backed out terminals

•	Improper mating

•	Broken locks

•	Improperly formed or damaged terminals

•	Poor terminal-to-wiring connections

•	Physical damage to the wiring harness

Clear the DTCs after completing the diagnosis. Test drive the vehicle for three drive cycles in order to verify that the DTC does not reset. Use the following procedure in order to complete one drive cycle:

Start the vehicle.
Drive the vehicle over 16 km/h (10 mph).
Stop the vehicle.
Turn the ignition to the OFF position.

Important: Zero the J 39200 test leads before making any resistance measurements. Refer to the J 39200 user's manual.

Step

Action

Value(s)

Yes

Was the Diagnostic System Check performed?

Go to Step 2

Go to Diagnostic System Check

Does DTC C1261 occur intermittently?

Go to Diagnostic Aids

Go to Step 3

Turn the ignition switch to the OFF position.
Disconnect the 6-way ABS brake motor pack connector.
Use the J 39200 in order to measure the resistance between the 6-way ABS brake motor pack connector terminal B and 6-way ABS motor pack connector terminal A

Is the resistance within the specified range?

0.2-1.5 ohms

Go to Step 4

Go to Step 8

Disconnect the EBCM connector.
Use J 39200 in order to measure the resistance between the 6-way ABS brake motor pack harness connector terminal B and the EBCM harness connector terminal C1.

Is the resistance within the specified range?

0-2 ohms

Go to Step 5

Go to Step 9

Use the J 39200 in order to measure the resistance between the 6-way ABS brake motor pack harness connector terminal A and the EBCM harness connector terminal D1.

Is the resistance within the specified range?

0-2 ohms

Go to Step 6

Go to Step 10

Inspect the following components for poor terminal contact and corrosion:

•	The 6-way ABS brake motor pack connector

•	The 6-way ABS brake motor pack harness connector

Inspect the following components for poor terminal contact and corrosion:

•	The EBCM connector

•	The EBCM harness connector

•	Damage that may cause an open with the connector connected.

Inspect CKT 9G01 and CKT 9H01 for damage. Damage may cause an open circuit.

Is there poor terminal contact or corrosion?

Go to Step 11

Go to Step 7

Reconnect the 6-way ABS brake motor pack connector.
Reconnect the EBCM connector.
Test drive the vehicle obtaining a speed at least 16 km/h (10 mph).
Turn the ignition switch to the OFF position.
Repeat the drive sequence two additional times.
Use the Scan Tool in order to inspect for DTCs.

Did DTC C1261 set as a current DTC in the last three drive cycles?

Go to Step 12

Go to Step 13

Replace the ABS brake motor pack. Refer to ABS Motor Pack Replacement .

Is the repair complete?

Go to Diagnostic System Check

Repair the open in CKT 9G01.

Is the repair complete?

Go to Diagnostic System Check

Repair the open in CKT 9H01.

Is the repair complete?

Go to Diagnostic System Check

Replace all of the terminals and connectors that exhibit the following conditions:

•	Poor terminal contact

•

Corrosion

•	Damaged terminal(s)

Is the repair complete?

Go to Diagnostic System Check

Replace the EBCM. Refer to Electronic Brake Control Module Replacement .

Is the repair complete?

Go to Diagnostic System Check

The malfunction is intermittent or not present at this time. Refer to Diagnostic Aids for more information.

Is the action complete?

System OK