Product Safety - Front Wheel Speed Sensor Corrosion

General Motors has decided that a defect which relates to motor vehicle safety exists in certain 1999-2002 Chevrolet Silverado, 2000-2002 Chevrolet Tahoe, Suburban, 2002 Chevrolet Avalanche, 1999-2002 GMC Sierra, 2000-2002 GMC Yukon, Yukon XL vehicles located in Ontario, Quebec, Newfoundland, New Brunswick, Nova Scotia, and Prince Edward Island. These vehicles may have a condition permitting corrosion to occur between the front hub/bearing assembly and the wheel speed sensor. If the brakes are applied while the vehicle is travelling at a speed of greater than 6 km/h (3.7 mph) but less than 16 km/h (10 mph), the corrosion may cause an unwanted anti-lock brake system (ABS) activation. If this condition occurred where stopping distance is limited, a crash could occur.

Dealers are to clean and treat the affected area, and in some cases, replace the front wheel speed sensor.

Involved are certain 1999-2002 Chevrolet Silverado, 2000-2002 Chevrolet Tahoe, Suburban, 2002 Chevrolet Avalanche, 1999-2002 GMC Sierra, 2000-2002 GMC Yukon, Yukon XL vehicles located in Ontario, Quebec, Newfoundland, New Brunswick, Nova Scotia, and Prince Edward Island and built within these VIN breakpoints:

Important: Dealers should confirm vehicle eligibility through GMVIS (GM Vehicle Inquiry System) before beginning recall repairs. [Not all vehicles within the above breakpoints may be involved.]

For dealers with involved vehicles, a Campaign Initiation Detail Report containing the complete Vehicle Identification Number, customer name and address data has been prepared and is being furnished to involved dealers. Dealers that have no involved vehicles currently assigned will not receive a report with the recall bulletin.

The Campaign Initiation Detail Report may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor vehicle registration data for any other purpose other than follow-up necessary to complete this recall is a violation of law in several states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to complete this program.

Parts required to complete this recall are to be obtained from General Motors Service Parts Operations (GMSPO). Please refer to your "involved vehicles listing" before ordering parts. Normal orders should be placed on a DRO=Daily Replenishment Order. In an emergency situation, parts should be ordered on a CSO=Customer Special Order.

Note: Very few vehicles will require front wheel speed sensor replacement; if required, order appropriate part from GMSPO.

The following procedure provides instructions for repairing a corrosion condition where the front wheel speed sensor mounts on the front wheel bearing assembly.

1. Raise the vehicle on a suitable hoist and support as necessary.
2. Remove both front tires and wheels.



3. Compress the front brake caliper pistons.

3.1.	Install a large C-clamp over the top of the caliper housing and against the back of the outboard pad.

3.2.	Slowly tighten the C-clamp until the pistons are pushed completely into the caliper bores.

3.3.	Remove the C-clamp from the caliper.





Important: It is not necessary to remove the front brake caliper from the bracket when removing the bracket in the next step.

4. Remove the two bolts that attach the front brake caliper mounting brackets to the knuckle.

Notice: Support the brake caliper with heavy mechanic's wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

5. Remove the brake caliper and bracket as an assembly and support it with heavy mechanic's wire or equivalent. DO NOT disconnect the hydraulic brake flexible hose from the caliper.
6. Mark the relationship of the rotor to the bearing hub.
7. If equipped, remove the rotor retaining push nuts from the wheel studs.



8. Remove the rotor.



9. Remove the bolt (1) that attaches the wheel speed sensor to the bearing hub.

Notice: Carefully remove the sensor by pulling it straight out of the bore. DO NOT use a screwdriver or other device to try to pry the sensor out of the bore. Prying will cause the sensor body to break off in the bore.

10. Remove the wheel speed sensor from the bearing hub assembly.




Important: The mounting surface on the sensor must be flat in the next step in order to be mounted correctly on the bearing hub assembly. If the mounting surface on the sensor is warped or bent, the sensor must be replaced.

11. Inspect to see if the mounting surface on the sensor is flat. Check the mounting surface on the sensor head for flatness by placing it on the edge of a metal machinist's scale or other suitable straight edge to measure the flatness. Check the sensor for flatness in multiple positions/directions (minimum 3).

•	If the sensor mounting surface is NOT flat (1), the sensor must be replaced. Proceed to the next step and replace the sensor.

•	If the sensor mounting surface IS flat (2), the sensor IS to be reused. Proceed to Step 16.




12. Remove the wheel speed harness mounting clips from the knuckle (4) upper control arm (3) and frame (2).
13. Disconnect the wheel speed sensor electrical connector (1) from the vehicle wiring harness.
14. Connect the new wheel speed sensor harness electrical connector to the vehicle wiring harness.
15. Attach the wheel speed sensor harness to the frame, upper control arm, and the knuckle.



16. Temporarily plug the wheel speed sensor hole (1) in the bearing hub to prevent debris from entering it when you clean it.

Important: All rust and corrosion must be removed from the wheel speed sensor mounting surfaces on the bearing hub in the next step.

17. Using a wire brush, sandpaper, emery cloth, scotch brite, or equivalent, thoroughly clean the wheel speed sensor mounting surface (2) on the bearing hub to remove any rust of corrosion.
18. Using compressed air, remove all debris from the bearing hub surface.
19. Using a clean shop towel, clean the sensor and the O-ring.

Important: While the corrosion is drying in the next step, begin performing Steps 3-20 on the opposite side front wheel speed sensor.

20. Apply (spray) two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) listed in this bulletin, to the complete sensor mounting surface on the bearing hub. Allow to dry for 3-5 minutes between coats.
21. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a light coating of the specified grease to the complete sensor mounting surface on the bearing hub and to the sensor and O-ring.
22. Remove the temporary plug from the hole in the bearing hub.
23. Install the wheel speed sensor in the bearing hub and install the bolt. Ensure that the sensor is seated flat against the hub.

Tighten
Tighten the wheel speed sensor mounting bolt to 18 N·m (13 lb ft).

24. Disconnect the front wheel speed sensor connector and place a digital volt meter (DVM) across the terminals of the wheel speed sensor connector. Rotate the bearing at approximately one revolution per second. The minimum reading should be at least 350 ACmVs. If the reading is less than 350 ACmVs, the wheel speed sensor must be replaced. Follow Steps 12-15 for instructions on replacing the wheel speed sensor. This step must be repeated after the new sensor has been installed.

Notice: Whenever the brake rotor has been separated from the wheel bearing flange, clean any rust or foreign material from the mating surface of the rotor and flange. Failure to do this may result in increased lateral runout of the rotor and brake.

Important: If the rotor was removed using the jack screw method, you must ensure that the hub flange is free of nicks or marks caused by this procedure. Remove all raised nicks or marks before installing the rotor.

25. Align the rotor to its original position on the hub and install the rotor.
26. Install the caliper and caliper mounting bracket assembly.
27. Perform the following procedure before installing the brake caliper bracket mounting bolts.

27.1.

Remove all traces of the original adhesive patch.

27.2.

Clean the threads of the bolt with brake parts cleaner, or the equivalent, and allow to dry.

27.3.

Apply threadlocker to the threads of the bolts.

28. Install the caliper bracket mounting bolts.

Tighten the brake caliper mounting bracket mounting bolts to the specification listed below.

Tighten

•	1500 Series vehicles -- 175 N·m (129 lb ft)

•	2500 Series vehicles -- 300 N·m (221 lb ft)

29. Install the front tire and wheel assembly.

Tighten
Tighten the wheel nuts to 190 N·m (140 lb ft).

30. Complete Steps 21-30 on the opposite side front wheel speed sensor.
31. Lower the vehicle.
32. With the engine OFF, gradually apply the brake pedal to approximately 2/3 of its travel distance.
33. Slowly release the brake pedal.
34. Wait 15 seconds and repeat Steps 32-33 until a firm pedal is obtained. This will properly seat the brake caliper pistons and brake pads.

Customer requests for reimbursement of previously paid repairs to correct the condition addressed in this bulletin are to be submitted by January 31, 2006.

All reasonable customer paid receipts should be considered for reimbursement. The amount to be reimbursed will be limited to the amount the repair would have cost if completed by an authorized General Motors dealer.

When a customer requests reimbursement, they must provide the following:

Claims for customer reimbursement on previously paid repairs are to be submitted as required by WINS.

Important: Refer to the GM Service Policies and Procedures Manual, section 1.6.2, for specific procedures regarding customer reimbursement verification.

The General Motors Courtesy Transportation program is intended to minimize customer inconvenience when a vehicle requires a repair that is covered by the New Vehicle Limited Warranty. The availability of courtesy transportation to customers whose vehicles are within the warranty coverage period and involved in a product recall is very important in maintaining customer satisfaction. Dealers are to ensure that these customers understand that shuttle service or some other form of courtesy transportation is available and will be provided at no charge. Dealers should refer to the General Motors Service Policies and Procedures Manual for Courtesy Transportation guidelines.

Submit a Product Recall Claim with the information indicated below:

Refer to the General Motors WINS Claims Processing Manual for details on Product Recall Claim Submission.

General Motors will notify customers of this recall on their vehicle (see copy of customer letter included with this bulletin).

All unsold new vehicles in dealers' possession and subject to this recall MUST be held and inspected/repaired per the service procedure of this recall bulletin BEFORE customers take possession of these vehicles.

Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time forward.

Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions contained in this bulletin. A copy of the customer letter is provided in this bulletin for your use in contacting customers. Recall follow-up cards should not be used for this purpose, since the customer may not as yet have received the notification letter.

In summary, whenever a vehicle subject to this recall enters your vehicle inventory, or is in your dealership for service in the future, please take the steps necessary to be sure the recall correction has been made before selling or releasing the vehicle.

Dear General Motors Customer:

General Motors has decided that a defect which relates to motor vehicle safety exists in certain 1999-2002 Chevrolet Silverado, 2000-2002 Chevrolet Tahoe, Suburban, 2002 Chevrolet Avalanche, 1999-2002 GMC Sierra, 2000-2002 GMC Yukon, Yukon XL vehicles located in Ontario, Quebec, Newfoundland, New Brunswick, Nova Scotia, and Prince Edward Island. These vehicles may have a condition permitting corrosion to occur between the front hub/bearing assembly and the wheel speed sensor. If the brakes are applied while the vehicle is travelling at a speed of greater than 6 km/h (3.7 mph) but less than 16 km/h (10 mph), the corrosion may cause an unwanted anti-lock brake system (ABS) activation. If this condition occurred where stopping distance is limited, a crash could occur.

Your dealer will clean and treat the affected area, and in some cases, replace the front wheel speed sensor. This service will be performed for you at no charge.

You may be contacted by a dealer other than the dealer who sold or is currently servicing your vehicle. Please be advised that you may take your vehicle to the General Motors dealership of your choice to have the recall service work completed. Please contact your dealer as soon as possible to arrange a service date.

If parts are required, ask your dealer for details regarding their availability. If parts are not in stock, they can be ordered before scheduling your service date.

This letter identifies your vehicle. Presentation of this letter to your dealer will assist their Service personnel in completing the necessary correction to your vehicle in the shortest possible time.

If you have already paid for some or all of the cost to replace the front wheel speed sensor(s) due to corrosion, and you have not received reimbursement under a Vehicle Service Contract, you should contact your dealer to seek reimbursement. Please provide your dealer with your original paid receipts or invoices verifying the repair, the amount charged, proof of payment, the date of payment of those charges, and proof of ownership of the vehicle at the time of the repair. Your request for reimbursement, including the information and documents mentioned above, must be received by your dealer by January 31, 2006. Reimbursement may be limited to the amount the repair would have cost if completed by an authorized General Motors dealer.

We are sorry to cause you this inconvenience; however, we have taken this action in the interest of your safety and continued satisfaction with our products.

Customer Support Department

General Motors of Canada Limited

04094