Battery Negative Cable Replacement 4.3 L Engine

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.



3. Remove the bolts securing the negative cable to the engine.
4. Remove the negative cable from the power steering accessory bracket (4WD 15 series).



5. Remove the bolt anchoring the negative battery cable to the block.
6. Remove the bolt anchoring the negative battery cable to the frame.
7. Remove the negative battery cable.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Install the negative battery cable.
2. Install the bolt anchoring the negative battery cable to the block.

Tighten
Tighten the bolt to 16 N·m (12 lb ft).

3. Install the bolt anchoring the negative battery cable to the frame.

Tighten
Tighten the bolt to 9 N·m (80 lb in).




4. Install the negative cable to the power steering accessory bracket (4WD 15 series).
5. Remove the safety stands.
6. Lower the vehicle.



7. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Battery Negative Cable Replacement 4.8,L 5.3L, 6.0L, and 8.1L

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .



2. If equipped with a 4.8L, 5.3L, or 6.0L engine, remove the battery cable bracket bolt and bracket from the power steering pump.



3. If equipped, disconnect the accessory power fuse block front wiring harness electrical connector from the negative cable connector.



4. If equipped with a 4.8L, 5.3L, or 6.0L engine, remove the negative cable clip from the positive cable clip.
5. Remove the engine wiring harness ground/negative cable bolt.
6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.



7. If equipped with a 8.1L engine, remove the negative cable clip from the positive cable clip.
8. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
9. Remove the engine wiring harness ground/negative cable bolt.
10. Reposition the wiring harness ground and negative cables.



11. Remove the forward lamp wiring harness ground/negative cable bolt.
12. Lower the vehicle.
13. Remove the negative battery cable.

1. Install the negative battery cable.
2. Raise the vehicle.
3. Position the negative cable and forward lamp wiring harness ring terminals to the frame.

Insert the anti-rotation tab on the forward lamp wiring harness into the hole in the frame.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the forward lamp wiring harness ground/negative cable bolt.

Tighten
Tighten the forward lamp wiring harness ground/negative cable bolt to 9 N·m (80 lb in).





Important: The engine wiring harness ground is to be installed under the negative cable ground.

5. If equipped with a 8.1L engine, position the wiring harness ground and negative cables. Position the anti-rotation tab on the negative cable in the correct location.
6. Install the engine wiring harness ground/negative cable bolt.

Tighten
Tighten the engine wiring harness ground/negative cable bolt to 25 N·m (18 lb ft).

7. Lower the vehicle.
8. Install the negative cable clip to the positive cable clip.



9. If equipped with a 4.8L, 5.3L, or 6.0L engine, position the negative cable and engine wiring harness ring terminals to the engine block. Position the anti-rotation tab on the negative cable in the correct location.
10. Install the engine wiring harness ground/negative cable bolt.

Tighten
Tighten the engine wiring harness ground/negative cable bolt to 25 N·m (18 lb ft).

11. Lower the vehicle.
12. Install the negative cable clip to the positive cable clip.



13. If equipped, connect the accessory power fuse block front wiring harness electrical connector to the negative cable connector.



14. If equipped with a 4.8L, 5.3L, or 6.0L engine, install the battery cable bracket and bolt to the power steering pump.

Tighten
Tighten the battery cable bracket bolt to 25 N·m (18 lb ft).




15. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Battery Negative Cable Replacement 6.6 L Engine

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.




1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .



2. Remove the negative cable clip from the clip on the positive cable.
3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
4. Remove the battery negative cable bolt.



5. Remove the forward lamp wiring harness ground/negative cable bolt.
6. Remove the negative battery cable.

1. Install the negative battery cable.
2. Position the negative cable and forward lamp wiring harness ring terminals to the frame.

Insert the anti-rotation tab on the forward lamp wiring harness into the hole in the frame.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the forward lamp wiring harness ground/negative cable bolt.

Tighten
Tighten the forward lamp wiring harness ground/negative cable bolt to 9 N·m (80 lb in).




4. Position the negative cable and engine wiring harness ring terminals to the engine block.

Position the anti-rotation tab on the negative cable in the correct location.

5. Install the engine wiring harness ground/negative cable bolt.

Tighten
Tighten the engine wiring harness ground/negative cable bolt to 34 N·m (25 lb ft).

6. Lower the vehicle.
7. Install the negative cable clip to the clip on the positive cable.



8. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .