GM Service Manual Online
For 1990-2009 cars only

Tools Required

    • J 3289-20 Holding Fixture
    • J 8092 Universal Driver
    • J 22912-B Rear Pinion and Axle Bearing Remover
    • J 36850 Transjel Lubricant
    • J 42176 Universal Driver Handle - Non-Threaded
    • J 42738 Seal Installer
    • J 43484 Front Output Shaft Seal Installer
    • J 45380 Transfer Case Rear Bushing Remover and Installer
    • J 45756 Rear Output Shaft Seal Installer
    • J 45757 Mainshaft Support Bushing and Bearing Installer
    • J 45759 Assembly Fixture

    Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 819661  Size: SH
  1. If removed, install the transfer case mounting studs.
  2. Tighten
    Tighten the mounting studs to 10 N·m (89 lb in).


    Object Number: 819573  Size: SH
  3. Attach the J 45759 to the front transfer case using the adapter studs. All of the assembly procedures can be performed with the case mounted to the J 45759 .
  4. Install the J 45759  (2) into the J 3289-20  (1) and secure with the pivot pin.

  5. Object Number: 819664  Size: SH
  6. If the vent is removed, apply pipe sealant GM P/N 12346004 (Canadian P/N 10953480) to the threads on the vent.
  7. Install the vent.
  8. Tighten
    Tighten the vent to 6 N·m (53 lb in).


    Object Number: 833018  Size: SH

    Important: Lubricate all of the bearings and bearing journals with transfer case fluid during installation.

  9. Install the input shaft bearing in the front case half.
  10. • Use a hammer and a brass drift only on the outer bearing race.
    • Ensure the bearing is kept square to the bore while installing.

    Object Number: 819641  Size: SH
  11. Install the front bearing, for the front output shaft, in the front case half.
  12. • Use a hammer and a brass drift only on the outer bearing race.
    • Ensure the bearing is kept square to the bore while installing.

    Object Number: 819644  Size: SH
  13. If it is a new shaft or if the cup plug was removed, install the cup plug in the front output shaft, using a suitable driver. Install the cup plug 1 mm (0.039 in) from flush with the end of the shaft.

  14. Object Number: 833012  Size: SH
  15. Install the front output shaft assembly.

  16. Object Number: 833010  Size: SH
  17. Install the input shaft.

  18. Object Number: 833007  Size: SH

    Important: If using the chain and sprockets again, ensure to align the marks of the drive chain and sprockets.

  19. Install the drive chain and sprockets. The blue link on the chain faces up.

  20. Object Number: 833005  Size: SH
  21. Install the front sun gear.

  22. Object Number: 819646  Size: SH

    Important: The planetary differential gears are timed to the sun gears. If the gears are not timed properly, the differential will not rotate without binding.

  23. With the rear side of the planetary differential facing up, align the marks on the pinion gears. Position the alignment marks with an area on the planetary housing that can be reference for all gears.

  24. Object Number: 833004  Size: SH
  25. Install the planetary differential assembly.
  26. • Do not rotate the planetary differential pinion gears when installing.
    • Ensure the alignment marks are still in position.

    Object Number: 833003  Size: SH
  27. Lubricate the sun gear thrust washer with J 36850 or equivalent.
  28. Install the sun gear thrust washer.

  29. Object Number: 833002  Size: SH
  30. Install the rear sun gear.
  31. • The shoulder side of the gear faces up.
    • Do not rotate the planetary pinion gears.

    Object Number: 833020  Size: SH
  32. Temporarily install the rear output shaft to the planetary differential and the rear sun gear.
  33. Rotate the rear output shaft three or four revolutions to rotate the planetary differential pinion gears. If properly aligned, the planetary pinion gears will rotate freely, and there will be no binding.
  34. Remove the rear output shaft without disturbing the rear sun gear.

  35. Object Number: 819637  Size: SH
  36. Install the front output shaft rear bearing in the rear case half.
  37. • Use a hammer and a brass drift only on the outer bearing race.
    • Ensure the bearing is kept square to the bore while installing.

    Object Number: 819638  Size: SH
  38. Using a hydraulic press and the J 22912-B , install the rear output shaft bearing.
  39. • The retaining ring groove on the bearing goes toward the input end or forward.
    • Use a suitable press plate on the end of the rear output shaft.
    • Ensure the bearing is supported on the inner race.

    Object Number: 819634  Size: SH
  40. Install a NEW retaining ring for the rear output shaft bearing.

  41. Object Number: 1708329  Size: SH
  42. Using the J 42176  (1) and the J 45757  (2), install the input shaft rear support bushing in the rear output shaft.

  43. Object Number: 819630  Size: SH
  44. Install the rear output shaft in the rear case half.
  45. 25.1. Spread the rear output shaft rear bearing outer retaining ring.
    25.2. Install, until the rear output shaft bearing outer retaining ring is seated in the bearing groove.

    Object Number: 833025  Size: SH

    Important: 

       • Ensure that both the sealing surfaces on the front and rear case halves are free of dirt, oil, and cleaning solvent.
       • Ensure the locating pins are installed in the case halves.

  46. Install the locating pins in the front case and rear case half, if necessary.
  47. Apply a 3.175 mm (1/8 in) bead of room temperature vulcanizing (RTV) sealant GM P/N 12345739 (Canadian P/N 10953541), or equivalent, to the mating surfaces of the front case half.

  48. Object Number: 819587  Size: SH
  49. Lower the rear case half into place.
  50. The rear output may require rotating to align the teeth with the planetary carrier.


    Object Number: 819583  Size: SH

    Notice: This component is made of magnesium. Proper assembly is required to prevent damage. Ensure the magnesium transfer case housings are properly insulated from all external steel components, or galvanic corrosion will occur. New nylon coated case bolts and aluminum washers must be used. Use only aluminum fill and drain plugs. Use only aluminum brackets under the case bolts. Ensure new seals are installed that have a rubber insulated outside diameter and have no tears or cuts. Extensive damage will occur if there is galvanic corrosion between the magnesium and steel components.

  51. Inspect the nylon coating on the case bolts for cuts or tears.
  52. Replace the case bolts if there is any damage to the nylon coating.
  53. Important: The case bolts are self-tapping; they must be hand started. Do not use power assisted tools to install the bolts.

  54. Install the case bolts, the washers, and the brackets.
  55. Tighten
    Tighten the case bolts to 21 N·m (15 lb ft).


    Object Number: 1549538  Size: SH
  56. Using J 45380 , install the output shaft bushing, if removed or new.

  57. Object Number: 833029  Size: SH
  58. Using J 45756 , install the rear output shaft seal.

  59. Object Number: 823193  Size: SH
  60. Apply pipe sealant GM P/N 12346004 (Canadian P/N 10953480) to the threads on the drain plug and fill plug.
  61. Install the drain plug and the fill plug.
  62. Tighten
    Tighten the drain plug and fill plug to 25 N·m (18 lb ft).


    Object Number: 819655  Size: SH
  63. Using the J 43484  (2) and the J 8092  (1), install the front output shaft seal.

  64. Object Number: 819657  Size: SH
  65. Using the J 42738 , install the front input shaft seal.
  66. Remove the transfer case from the J 45759 .