GM Service Manual Online
For 1990-2009 cars only

Audible Spark Knock (Detonation), MIL Illuminated, DTC P0332 Set (Replace Rear Bank Knock Sensor and RTV Area Around Sensor)

Subject:Audible Spark Knock (Detonation), MIL Illuminated, DTC P0332 Set (Replace Rear Bank Knock Sensor and RTV Area Around Sensor)

Models:1998-2002 Chevrolet Camaro, Corvette
1998-2002 Pontiac Firebird
with 5.7L Engine (VIN G -- RPO LS1)
1999-2002 Chevrolet Silverado, Suburban, Tahoe
2002 Chevrolet Avalance
1999-2002 GMC Sierra, Yukon, Yukon XL
2002 Cadillac Escalade, Escalade EXT
with 4.8L, 5.3L or 6.0L Engine (VINs V, T, Z, N, U -- RPOs LR4, LM7, L59, LQ9, LQ4)



This bulletin is being revised to add Cadillac Escalade and Cadillac Escalade EXT to the Models. Please discard Corporate Bulletin Number 02-06-04-023 (Section 6 -- Engine/Propulsion System).


Condition

Some customers may comment on a mild to severe engine ping (commonly referred to as spark knock), usually worse during acceleration and/or an illuminated MIL. Upon investigation, the technician may find DTC P0332 set.

Cause

This condition may be the result of corrosion of the rear bank knock sensor due to water intrusion into the sensor cavity. This condition is more apparent on vehicles in which customers frequently wash the engine compartment.

Correction

Replace the rear bank knock sensor and build a dam (wall) around the sensor using RTV to divert water away from the sensor. Use the procedure and part number listed below.

  1. Remove the intake manifold. Refer to the Intake Manifold Replacement procedure in the Engine Controls sub-section of the appropriate Service Manual.

  2. Object Number: 54608  Size: SH
  3. Remove the wiring harness assembly from the knock sensor.

  4. Object Number: 54612  Size: SH
  5. Remove the rear bank knock sensor.
  6. Install the new rear bank knock sensor.
  7. Tighten
    Tighten the knock sensor to 20 N·m(15 lb ft).

  8. Install the wiring harness assembly to the knock sensor.

  9. Object Number: 881977  Size: SH
  10. Apply a bead of RTV silicone sealant approximately 9 mm (3/8 in) wide and 6 mm (1/4 in) high along the outside edge of the ridge on the engine block valley cover around the rear bank knock sensor. DO NOT form a complete circle. Leave the rear section open as shown.
  11. From the underside of the intake manifold, completely remove the rear intake manifold seal (foam material).
  12. Install the intake manifold. Refer to the Intake Manifold Replacement procedure in the Engine Controls sub-section of the appropriate Service Manual.

Parts Information

Part Number

Description

Qty

10456603

Sensor, Knock

1

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use:

Labor Operation

Description

Labor Time

J4437

(F-Car)

Sensor, Knock -- Replace

1.7 hrs

Add

(1998-1999 F-Car Only)

To Remove EGR

0.2 hr

J4437

(Y-Car)

Sensor, Knock -- Replace

1.6 hrs

J4437

(C/K-Truck)

Sensor, Knock -- Replace

1.5 hrs

Add

(C/K Truck Only)

With Three Piece Engine Covers

0.2 hr

Add

(All)

Diagnosis Time

0.3 hr

Add

(All)

To RTV Area Around Sensor and Remove Intake Manifold Seal

0.2 hr