GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 1999 🢒 Tahoe - 2WD 🢒 Engine 🢒 Engine Controls - 6.5L 🢒 DTC P0567 Cruise Control Resume Switch Circuit

Object Number: 185074 Size: LF
Engine Controls Components
4WD and Cruise Controls
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The cruise resume/accel switch is an input to the fuel control portion of the PCM. These inputs allow the PCM to control and hold a requested speed. The cruise resume/accel switch sends ignition voltage to the PCM when the switch is closed (ON).

Conditions for Running the DTC
    • The PCM performs this DTC diagnostic continuously.
    • The ignition switch in the ON position.

Conditions for Setting the DTC

Ignition voltage on resume request signal circuit when the cruise control ON/OFF switch in the OFF position.

or

    • Resume switch ON for longer than 25.5 seconds the cruise control ON/OFF switch in the ON position.
    • All of the diagnostic set conditions met for 2 seconds.

Action Taken When the DTC Sets
    • The PCM disallows all cruise control inputs.
    • TCC shift schedules may be affected.
    •  The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
    • The PCM records the operating conditions at the time the diagnostic fails. This information is stored in the Failure Records.

Conditions for Clearing the MIL/DTC
    • A History DTC clears after forty consecutive warm-up cycles, if this or any other emission related diagnostic does not report any failures
    • The use of a scan tool.

Diagnostic Aids

Check for a resume/accel switch stuck in the engage position or the signal circuit is shorted to voltage.

Test Description

Number(s) below refer to the step number(s) on the Diagnostic Table.

  1. This step determines if the signal circuit is shorted to voltage.

    2.

  2. This step determines if the PCM or switch is at fault.

Step

Action

Value(s)

Yes

No

1

Important: Before clearing any DTCs, use the scan tool Capture Info to save freeze frame and failure records for reference, as the Scan tool loses data when using the Clear Info function.

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

  1. Connect a Scan tool.
  2. Turn the ignition ON leaving the engine OFF.
  3. Turn the Cruise switch OFF.

Does the scan tool display Resume Switch ON?

--

Go to Step 3

Go to Step 4

3

  1. Turn the ignition ON leaving the engine OFF.
  2. Disconnect the PCM connector containing the Resume switch signal circuit.
  3. Probe the Resume switch signal circuit at the PCM harness with a test light connected to chassis ground.

Is the test light ON?

--

Go to Step 5

Go to Step 6

4

The DTC is intermittent. If no additional DTCs are stored, refer to Diagnostic Aids. If additional DTCs were stored refer to the applicable DTC table(s) first.

Are any additional DTCs stored?

--

Go to the Applicable DTC Table

Go to Diagnostic Aids

5
  1. The Resume switch signal circuit is shorted to voltage or stuck in the ON position.
  2. Repair the problem as necessary.

Is the action complete?

--

Go to Step 8.

--

6

Replace the PCM.

Important: The new PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming .

Is the action complete?

--

Go to Step 7

--

7
  1. Using the Scan tool, clear the DTCs.
  2. Start engine and idle at normal operating temperature.
  3. Select DTC, Specific, then enter the DTC number which was set.
  4. Operate the vehicle, with the Conditions for Setting this DTC, until the Scan Tool indicates the diagnostic Ran.

Does the Scan Tool indicate the diagnostic Passed?

--

Go to Step 8

Go to Step 2

8

Does the Scan tool display any additional undiagnosed DTCs?

--

Go to the Applicable DTC Table

System OK