Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provide an overview of each diagnostic category. |
DTC Descriptors
DTC P0112: Intake Air Temperature (IAT) Sensor Circuit Low VoltageDTC P0113: Intake Air Temperature (IAT) Sensor Circuit High Voltage
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
IAT Sensor Signal | P0112 | P0113 | P0113¹ | -- |
Low Reference | -- | P0113 | P0113² | -- |
¹ Sensor damage may occur if the circuit is shorted to B+. ² Internal ECM damage may occur if the circuit is shorted to B+. | ||||
Typical Scan Tool Data
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Engine operating in Closed Loop. Parameter Normal Range: Varies with ambient temperature. | |||
IAT Sensor Signal | 129°C (264°F), 0.0 Volts | -40°C (-40°F), 5.0 Volts | -40°C (-40°F), 5.0 Volts |
Low Reference | -- | -40°C (-40°F), 5.0 Volts | -40°C (-40°F), 5.0 Volts¹ |
¹ Internal ECM damage may occur if the circuit is shorted to B+. | |||
Circuit Description
The intake air temperature (IAT) sensor is a variable resistor that measures the temperature of the air entering the engine. The IAT sensor has a signal circuit and a low reference circuit. The engine control module (ECM) supplies 5 volts to the IAT signal circuit and a ground for the IAT low reference circuit.
The following table illustrates the difference between temperature, resistance, and voltage:
IAT | IAT Resistance | IAT Signal Voltage |
|---|---|---|
Cold | High | High |
Warm | Low | Low |
Conditions for Running the DTC
| • | The ignition is ON or the engine is running. |
| • | The DTCs run continuously once the above condition is met. |
Conditions for Setting the DTC
P0112
The ECM detects that the IAT sensor voltage is less than 0.01 volt for more than 3 seconds.
P0112
The ECM detects that the IAT sensor voltage is greater than 4.99 volts for more than 3 seconds.
Action Taken When the DTC Sets
DTC P0112 and P0113 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTC P0112 and P0113 are Type B DTCs.
Diagnostic Aids
| • | If the vehicle has sat overnight, the IAT sensor and the ECT sensor values should display within 3°C (5°F). |
| • | High resistance on either the IAT sensor signal circuit or the IAT sensor low reference circuit may not set a DTC. |
Reference Information
Schematic Reference
Connector End View Reference
Engine Controls Connector End Views
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Circuit/System Verification
- With the engine idling for 1 minute, observe the DTC information with a scan tool. DTC P0112 and P0113 should not set.
- If the vehicle passes the Circuit/System Verification test, then operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the IAT sensor.
- Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal and battery ground.
- Test for less than 0.5 volt between the low reference circuit and ground.
- Install a 3-amp fused jumper wire between the signal circuit and the low reference circuit. Verify the IAT sensor parameter is greater than 128°C (262°F).
- If all circuits/connections test normal, test or replace the IAT sensor.
| ⇒ | If less than 4.8 volts, test the signal circuit for a short to ground or an open. If the circuit/connections test normal, replace the ECM. |
Important: If the signal circuit is shorted to voltage the sensor may be damaged.
| ⇒ | If greater than 5.2 volts, test the signal circuit for a short to voltage. If the circuit/connections test normal, replace the ECM. |
| ⇒ | If greater than 0.5 volt, test the low reference circuit for a short to voltage. If the circuit/connections test normal, replace the ECM. |
| ⇒ | If less than 128°C (262°F), test the signal circuit and the low reference circuit for an open/high resistance. If the circuit/connections test normal, replace the ECM. |
Component Testing
- Ignition OFF, disconnect the harness connector of the IAT sensor.
- Test the IAT sensor by varying the sensor temperature while monitoring the sensor resistance. Compare the readings with the Temperature Versus Resistance table and verify that the resistance is within 5 percent of the specification.
Important: A thermometer can be used to test the sensor off the vehicle.
| ⇒ | If the resistance vs temperature is not within 5 percent, replace the IAT sensor. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for engine control module replacement, setup, and programming |
