Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provide an overview of each diagnostic category. |
DTC Descriptors
DTC P0102: Mass Air Flow (MAF) Sensor Circuit Low FrequencyDTC P0103: Mass Air Flow (MAF) Sensor Circuit High Frequency
Diagnostic Fault Information
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
|---|---|---|---|---|---|
Ignition 1 Voltage | P0102 | P0101 | P0102 | P2510 | P0101 |
MAF Sensor Signal | P0102 | P0101 | P0102 | P0101, P0102, P0401 | P0101 |
Low Reference | -- | -- | -- | -- | -- |
Typical Scan Tool Data
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Engine running at idle, ECT sensor greater than 60°C (140°F) Parameter Normal Range: 10-20 g/s Operating Conditions: Engine running at idle, ECT sensor less than 60°C (140°F) Parameter Normal Range: 30-40 g/s | |||
Ignition 1 Voltage | 0.0 g/s | 0.0 g/s | -- |
MAF Sensor Signal | 0.0 g/s | 0.0 g/s | 0.0 g/s |
Low Reference | -- | -- | -- |
Circuit/System Description
The mass air flow (MAF) sensor is integrated with the intake air temperature (IAT) sensor. The MAF sensor is an air flow meter that measures the amount of air entering the engine. The engine control module (ECM) uses the MAF sensor signal to provide the correct fuel delivery for all engine speeds and loads. A small quantity of air entering the engine indicates a deceleration or idle condition. A large quantity of air entering the engine indicates an acceleration or high load condition.
The ECM applies 5 volts to the MAF sensor on the MAF sensor signal circuit. The sensor uses the voltage to produce a frequency based signal on the inlet airflow through the sensor bore. The frequency varies in a range depending on engine coolant temperature (ECT) sensor 1 of approximately 2,300 Hertz at idle to near 9,000 Hertz at maximum engine load.
When engine coolant temperatures reach 60°C (140°F) the ECM commands a Rich Idle mode. During Rich Idle the EGR valve is commanded ON, and a lower frequency and g/s value will be indicated on the scan tool.
Conditions for Running the DTC
P0102
| • | The engine is running for greater than 2 seconds. |
| • | The engine speed is between 500-3,100 RPM. |
| • | The above conditions are met for greater than 3 seconds. |
| • | This DTC runs continuously within the enabling conditions. |
P0103
| • | The engine is running for greater than 2 seconds |
| • | The above conditions are met for greater than 3 seconds. |
| • | This DTC runs continuously within the enabling conditions. |
Conditions for Setting the DTC
P0102
The ECM detects that the MAF sensor is less than 3.6 g/s for greater than 3 seconds.
P0103
The ECM detects that the MAF sensor is greater than 527 g/s for greater than 3 seconds.
Action Taken When the DTC Sets
| • | DTCs P0102 and P0103 are Type B DTCs. |
| • | The ECM commands reduced engine power. |
| • | DPF Regeneration is Inhibited. |
| • | The driver information center (DIC) or indicator may display reduced engine power. |
Conditions for Clearing the DTC
DTCs P0102 and P0103 are Type B DTCs.
Diagnostic Aids
| • | A wide open throttle (WOT) acceleration from a stop should cause the MAF Sensor parameter on the scan tool to increase rapidly. This increase should be from 6-8 g/s at idle to greater than 380 g/s at the time of the 1-2 shift. |
| • | For an intermittent problem, visually and physically inspect the exhaust gas recirculation (EGR) valve for a possible binding or sticking in the open position. |
| • | Verify that any electrical aftermarket devices are properly connected and grounded. Refer to Checking Aftermarket Accessories. |
Reference Information
Schematic Reference
Connector End View Reference
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Special Tools
J 38522 Variable Signal Generator
Circuit/System Verification
- Verify that the following DTCs are not set: P003A, P0047, P0048, P0106, P0403, P0405, P0406, P046C, P02E2, P02E3, P02E7, P02E8, or P02E9.
- Engine running at idle, observe the scan tool MAF Sensor parameter. The reading should be between 10-38 g/s depending on the ECT sensor.
- Operate the vehicle within the Conditions for Running the DTC to verify that the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
| ⇒ | If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle |
Circuit/System Testing
- Verify the integrity of the entire air induction system by inspecting for the following conditions:
- Ignition OFF, disconnect the harness connector at the MAF/IAT sensor.
- Ignition OFF and scan tool disconnected for 90 seconds, test for less than 5 ohms between the MAF low reference circuit terminal 2 and ground.
- Ignition OFF and scan tool disconnected for 90 seconds, test for less than 5 ohms between the IAT sensor 1 low reference circuit terminal 4 and ground.
- Ignition ON, verify that a test lamp illuminates between the ignition 1 voltage circuit terminal 3 and ground.
- Ignition ON, test for 4.8-5.2 volts between the MAF signal circuit and ground.
- Remove the Intake Manifold Tube. Refer to Intake Manifold Tube Replacement.
- Visually inspect the EGR valve and verify the valve is in the closed position.
- Ignition OFF, connect the red lead of the J 38522 to the signal circuit terminal 1 at the MAF/IAT sensor harness connector. Connect the battery voltage supply to B+. Connect the black lead to ground.
- Set the J 38522 signal switch to 5 volts, the frequency to 5K, and the Duty Cycle to Normal.
- Engine idling, observe the scan tool MAP sensor parameter. The scan tool MAF Sensor parameter should be between 4,950-5,025 Hz.
- If all circuits and the EGR valve test normal, replace the MAF/IAT sensor.
| • | Damaged components |
| • | Loose or improper installation |
| • | Restrictions or leaks in the air induction system |
| • | Water intrusion |
| • | In cold climates, inspect for any snow or ice build-up at the air cleaner and MAF sensor. |
| ⇒ | If greater than the specified range, test the MAF low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than the specified range, test the IAT sensor 1 low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If the test lamp does not illuminate, test the ignition 1 voltage circuit for a short to ground or an open/high resistance. |
| ⇒ | If less than the specified range, test the MAF signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than the specified range, test the MAF signal circuit for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If the EGR valve is not in the closed position, replace the EGR valve. |
| ⇒ | If the EGR valve inspection is normal, replace the MAF/IAT sensor. |
| ⇒ | If the MAF Sensor parameter is not within the specified range, replace the ECM. |
Repair Instructions
| • | Control Module References for ECM replacement, setup, and programming |
Repair Verification
- Install any components or connectors that have been removed or replaced during diagnosis.
- Perform any adjustment, programming, or setup procedures that are required when a component or module is removed or replaced.
- Clear the DTCs.
- Turn OFF the ignition for 90 seconds.
- Duplicate the Conditions for Running the DTC and use the Freeze Frame/Failure Records, if applicable, in order to verify the DTC does not reset. If the DTC resets or another DTC is present, refer to Diagnostic Trouble Code (DTC) List - Vehicle and perform the appropriate diagnostic procedure.
- Perform the Diesel Particulate Filter (DPF) Service Regeneration.
