GM Service Manual Online
For 1990-2009 cars only

Heated Mirrors Inoperative w/AN3, DL3

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Mirror Heating Element Control

1

1

1

--

Low Reference

--

1

1

--

1. Heated Mirror Malfunction

Circuit/System Description

The heated mirrors are connected to the DDM and PDM. The DDM and the PDM receive a GMLAN serial data message from the HVAC control module indicating that the rear window defogger switch has been activated. If conditions are correct, the DDM and PDM will apply battery voltage to the outside rearview mirror heating element control circuits, and ground to the low reference circuits.

Reference Information

Schematic Reference

Outside Rearview Mirror Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Outside Mirror Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information.

Circuit/System Verification

  1. Ignition ON, press the rear window defogger switch. Verify the rear window defogger indicator illuminates.
  2. If the rear window defogger indicator does not illuminate, refer to Rear Window Defogger Malfunction.
  3. Verify both the left and right outside mirror glass become warm.

Circuit/System Testing

  1. Ignition OFF, disconnect the X3 harness connector at the appropriate door module.
  2. Ignition ON, verify a test lamp does not illuminate between the control circuit terminal 7 and ground.
  3. If the test lamp illuminates, test the control circuit for a short to voltage.
  4. Ignition OFF, test for infinite resistance between the control circuit terminal 7 and ground.
  5. If less than the specified value, test the control circuit for a short to ground. If the circuit tests normal, test or replace the rearview mirror face.
  6. Test for 5-10 ohms of resistance between the control circuit terminal 7 and the low reference circuit terminal 3.
  7. If not within the specified range, test the control circuit and the low reference circuit for an open/high resistance. If the circuits test normal, test or replace the rearview mirror face.
  8. If all circuits test normal, test or replace the door module.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Outside Rearview Mirror Glass Replacement
    •  Control Module References for DDM, and PDM replacement, setup, and programming

Heated Mirrors Inoperative w/o AN3, DL3

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Heated Mirror Element Control

1

1

2

--

Ground

--

1

--

--

1. Heated Mirror Inoperative

2. Heated Mirror Always On

Circuit/System Description

The REAR DEFOG relay supplies voltage to the outside rearview mirror heater elements based on the current state of the rear window defogger. The relay supplies B+ through the driver/passenger mirror heating element control circuit when a request is seen.

Reference Information

Schematic Reference

Outside Rearview Mirror Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Outside Mirror Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information.

Circuit/System Verification

  1. Ignition ON, press the rear window defogger switch. Verify the rear window defogger turns ON and the rear window becomes warm.
  2. If the rear window defogger does not turn on, refer to Rear Window Defogger Malfunction.
  3. Verify both the left and right outside mirror glass become warm.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the outside rearview mirror.
  2. Test for less than 10 ohms between the ground circuit terminal 3 and ground.
  3. If greater than the specified value, test the ground circuit for an open/high resistance.
  4. Connect a test lamp between the heater element control circuit terminal 7 and ground.
  5. Ignition ON, operate the rear window defogger ON and OFF with the rear defogger switch. The test lamp should turn ON and OFF when changing between the commanded states.
  6. If the test lamp is always ON, test the control circuit for a short to voltage.
    If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance.
  7. If all circuits test normal, test or replace the outside rearview mirror glass.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Outside Rearview Mirror Glass Replacement