GM Service Manual Online
For 1990-2009 cars only

Wheel Drive Shaft Replacement 2500

Tools Required

J 45859 Axle Remover

Removal Procedure

Caution: Do not attempt to move vehicle with drive axle(s) removed from wheel bearing. Wheel(s) could fall off, dropping vehicle to the ground and causing personal injury or damage to the vehicle.


    Object Number: 673322  Size: SH
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Remove the wheel and tire assembly. Refer to Tire and Wheel Removal and Installation .
  3. Remove the drive axle center cap, if equipped.

  4. Object Number: 870456  Size: SH
  5. Insert a drift or a large screwdriver through the brake caliper into one of the brake rotor vanes in order to prevent the drive axle wheel drive shaft from turning.
  6. Remove the nut and the washer from the hub. Do not reuse the nut. A new nut must be used when installing the wheel drive shaft.
  7. Using the J 45859 or equivalent, press the wheel drive shaft from the hub.

  8. Object Number: 320653  Size: SH
  9. Remove the 6 bolts (1) securing the wheel drive shaft inboard flange to the output shaft flange.
  10. Remove the drift from the rotor.
  11. Remove the stabilizer shaft link from the lower control arm. Refer to Stabilizer Shaft Replacement .
  12. Wrap shop towels around both the inner and the outer wheel drive shaft boots in order to avoid damage to the boots during removal and installation.
  13. Pull the wheel drive shaft through the lower control arm opening.

Installation Procedure


    Object Number: 320653  Size: SH
  1. Wrap shop towels around both the inner and the outer wheel drive shaft boots in order to avoid damage to the boots during removal and installation.
  2. Important: Clean the steering knuckle and the wheel drive shaft splines and threads. These areas must be dry and free of grease, dirt, and contamination.

  3. Insert the wheel drive shaft splined shank into the knuckle hub.
  4. Notice: Use only a genuine GM front wheel drive shaft nut. Installation of anything but an OEM front wheel drive shaft nut could cause damage to the vehicle.

  5. Install the washer (3) and the new hub nut (2) to the wheel drive shaft.
  6. Do not tighten the new hub nut at this time.

  7. Attach the wheel drive shaft inboard flange to the output shaft flange using the inboard flange bolts (1).

  8. Object Number: 1932  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  9. Insert a drift or a large screwdriver through the brake caliper into 1 of the brake rotor vanes in order to prevent the wheel drive shaft from turning.
  10. Tighten

        • Tighten the inboard flange bolts to 79 N·m (58 lb ft).
        • Tighten the hub nut to 240 N·m (177 lb ft).
  11. Remove the drift from the rotor.

  12. Object Number: 673322  Size: SH
  13. Install the drive axle center cap, if equipped.
  14. Install the stabilizer shaft link. Refer to Stabilizer Shaft Replacement .
  15. Install the wheel and tire assembly. Refer to Tire and Wheel Removal and Installation .
  16. Lower the vehicle.

Wheel Drive Shaft Replacement 1500

Caution: Do not attempt to move vehicle with drive axle(s) removed from wheel bearing. Wheel(s) could fall off, dropping vehicle to the ground and causing personal injury or damage to the vehicle.

Tools Required

J 45859 Axle Remover

Removal Procedure

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation .

  3. Object Number: 1932  Size: SH
  4. Insert a drift or large screwdriver through the brake caliper into one of the brake rotor vanes in order to prevent the wheel drive shaft from turning.

  5. Object Number: 1736696  Size: SH

    Important: DO NOT reuse the wheel drive shaft nut, use a NEW nut only.

  6. Remove the nut (1) and washer (2) from the hub.

  7. Object Number: 870456  Size: SH
  8. Using the J 45859 or equivalent, remove the wheel drive shaft from the hub.
  9. Remove the special tool.

  10. Object Number: 1736718  Size: SH
  11. Remove the retaining bolts from the drive flange.
  12. Remove the drift or large screwdriver from the brake rotor.
  13. Remove the stabilizer shaft link from the lower control arm. Refer to Stabilizer Shaft Replacement .
  14. Remove the shock module. Refer to Shock Absorber and Spring Assembly Replacement .

  15. Object Number: 1736759  Size: SH
  16. Remove the wheel drive shaft through the lower control arm opening.
  17. Remove all dirt and debris from the splines on the wheel hub/bearing.

Installation Procedure


    Object Number: 1736759  Size: SH
  1. Install the wheel drive shaft in the steering knuckle.

  2. Object Number: 1736696  Size: SH

    Important: Install the NEW nut and washer, but DO NOT tighten at this time.

  3. Install the NEW nut (1) and washer (2).

  4. Object Number: 1736718  Size: SH
  5. Install the retaining bolts and finger tighten.

  6. Object Number: 1932  Size: SH
  7. Insert a drift or large screwdriver through the brake caliper into one of the brake rotor vanes in order to prevent the wheel drive shaft from turning.
  8. Notice: Refer to Fastener Notice in the Preface section.

  9. Tighten the wheel driver shaft retaining bolts.
  10. Tighten
    Tighten the retaining bolts to 79 N·m (58 lb ft).

  11. Tighten the wheel drive shaft retaining nut.
  12. Tighten
    Tighten the retaining nut to 240 N·m (177 lb ft).

  13. Remove the drift or large screwdriver from the brake rotor.
  14. Install the shock module. Refer to Shock Absorber and Spring Assembly Replacement .
  15. Install the stabilizer shaft link from the lower control arm. Refer to Stabilizer Shaft Replacement .
  16. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation .
  17. Lower the vehicle.