GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The fuel level sensor changes resistance in response to fuel level. The powertrain control module (PCM) monitors the signal circuit of the fuel level sensor in order to determine the fuel level. When the fuel tank is full, the sensor resistance is low and the PCM senses a low signal voltage. When the fuel tank is empty, the sensor resistance is high and the PCM senses a high signal voltage. The PCM uses the signal circuit of the fuel level sensor in order to calculate the percentage of remaining fuel in the tank. The PCM sends the fuel level percentage via the class 2 serial data circuit to the instrument cluster in order to control the fuel gage. The fuel level information is also used for misfire and evaporative emission (EVAP) diagnostics.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0462 Fuel Level Sensor 1 Circuit Low Voltage

Conditions for Running the DTC

The engine is running.

Conditions for Setting the DTC

    • The sender output is less than 0.39 volts.
    • The above condition is present for greater than 30 seconds.

Action Taken When the DTC Sets

    • The fuel gage defaults to empty.
    • The low fuel indicator illuminates.
    • The PCM records the operating conditions at the time that the diagnostic test fails. The PCM displays the failure information in the Failure Records on the scan tool.

Conditions for Clearing the DTC

    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The history DTC clears after 40 malfunction-free warm-up cycles.
    • The PCM receives the clear code command from the scan tool.

Diagnostic Aids

Use the Freeze Frame/Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records data may help in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also help in determining the number of ignition cycles that the diagnostic test reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate at what point the DTC failed.

Refer to Testing for Intermittent Conditions and Poor Connections .

Test Description

The number below refers to the step number on the diagnostic table.

  1. This step tests for the proper operation of the circuit in the high voltage range.

Step

Action

Values

Yes

No

Schematic Reference: Instrument Cluster Schematics

Connector End View Reference: Master Electrical Component List

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Install the scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. With the scan tool, observe one of the following fuel level parameters:
  4. • Fuel Tank Level Remaining parameter in the powertrain control module (PCM) Enhanced evaporative emission (EVAP) Data, data list-gas only.
    • Fuel Level Sensor parameter in the PCM Fuel System data list - 6.6L diesel only.

Does the scan tool indicate that the Fuel Tank Level Remaining parameter is greater than the specified value or the Fuel Level Sensor parameter is less than the specified value?

98%

0.5 V - 6.6L diesel only

Go to Step 3

Go to Diagnostic Aids

3

  1. Turn the ignition OFF.
  2. Disconnect C152.
  3. Turn the ignition ON, with the engine OFF.
  4. With the scan tool, observe the fuel level parameter.

Does the scan tool indicate that the Fuel Tank Level Remaining parameter is less than the specified value or the Fuel Level Sensor parameter is greater than the specified value?

4%

4.5 V - 6.6L diesel only

Go to Step 5

Go to Step 4

4

Test the signal circuit of the fuel level sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 10

Go to Step 7

5

Test the signal circuit of the fuel level sensor for a short to ground between C152 and the fuel level sensor. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 10

Go to Step 6

6

Inspect for poor connections at the harness connector of the fuel level sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 10

Go to Step 8

7

Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 10

Go to Step 9

8

Replace the fuel level sensor. Refer to the following procedures:

    •  Fuel Level Sensor Replacement for the 4.3L engine
    •  Fuel Level Sensor Replacement for the 4.8L, 5.3L, and 6.0L engines
    •  Fuel Level Sensor Replacement for the 6.6L (LBZ and LLY) engine
    •  Fuel Level Sensor Replacement for the 8.1L engine

Did you complete the replacement?

--

Go to Step 10

--

9

Replace the PCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 10

--

10

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK