Rear Seat Replacement 2-Door Utility

Important: Remove the passenger side seat before removing the driver side seat.

1. Remove the seat leg trim covers.



2. Tilt the seat back slightly forward in order to remove the seat leg nuts.
3. Fold the seat in order to remove the rear seat nuts.
4. Remove the seat from the vehicle.

1. Install the seat to the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Fold the seat back forward in order to install the rear seat mounting nuts.

Tighten
Tighten the rear seat mounting nuts to 80 N·m (59 lb ft).

3. Install the seat leg trim covers.

Ensure that the covers lock into place.




4. Install the seat leg trim covers.

Ensure that the covers lock into place.

Rear Seat Replacement 4-Door Utility

Important: Remove the passenger side rear seat before removing the driver side rear seat.

1. Remove the seat leg trim covers.



2. Tilt the seat back slightly forward in order to remove the seat leg nuts.
3. Fold the seat in order to remove the rear seat nuts.
4. Remove the seat from the vehicle.

1. Install the seat to the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Fold the seat back forward in order to install the rear seat mounting nuts.

Tighten
Tighten the rear seat mounting nuts to 80 N·m (59 lb ft).




3. Install the seat leg trim covers.

Ensure that the covers lock into place.

Rear Seat Replacement Crew Cab

1. Remove the 2 bolts securing the rear seat bottom to the floor.
2. Carefully pull seat cushions ears to release retainers from the seat back mounting bracket.
3. Lift the rear seat bottom out of the vehicle.



4. Remove the 2 bolts securing the rear seat back to the floor.
5. Remove the 2 nuts and washers securing the rear seat back to the floor studs.
6. Remove the rear seat back from the vehicle.

1. Position the rear seat back in the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the 2 bolts securing the rear seat back to the floor.

Tighten
Tighten the rear seat back mounting bolts to 80 N·m (59 lb ft).

3. Install the 2 washers and nuts securing the rear seat back to the floor studs.

Tighten
Tighten the rear seat back nuts to 80 N·m (59 lb ft).




4. Install the rear seat bottom to vehicle. Insure seat bottom frame is engaged with tabs in seat back mounting bracket.
5. Install the 2 bolts retaining the rear seat bottom to the floor.

Tighten
Tighten the rear seat bottom bolts to 25 N·m (18 lb ft).

6. Install the seat bottom cushion ear retainers into the seat back mounting bracket.