Caution: Provide additional support when a vehicle is on a hoist in the following ways:

Notice: The fuel tank equipped with ORVR components require special handling. Follow all instructions for servicing the fuel tank as specified in the service procedures. Damage to the fuel system components and the failure to meet the Federal Regulations may result from incorrect servicing of the fuel tank.

1. Relieve fuel system pressure. Refer to Fuel Pressure Relief .
2. Drain the fuel tank. Refer to Fuel Tank Draining .
3. Remove the rear seat bottom cushion. Refer to Rear Seat Cushion Replacement in Seats.



4. Remove the fuel sender assembly access panel (1) from the rear seat floor. Tthe panel is held in place by a butyl caulk seal.



5. Disconnect the electrical connector (1) from the fuel sender assembly .



6. Remove the retaining clip (1) from the fuel line fitting .
7. Disconnect the fuel line (2) from the fuel sender assembly.
8. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.



9. Remove the catalytic converter and intermediate pipe assembly (2) from the vehicle. Refer to Catalytic Converter Replacement in Engine Exhaust.
10. Remove the 4 screws and the nut from the rear exhaust heat shield (1).
11. Remove the rear exhaust heat shield (1) from the underbody.
12. Remove the 4 bolts securing the parking brake cables to the underbody.



13. Remove the fuel filler hose (2) from the fuel tank (5).
14. Disconnect the fuel tank breather hose (3) from the fuel tank.
15. Disconnect the ORVR vapor hose (1) from the fuel filler pipe assembly.



16. Disconnect the fuel limiter vent valve hose (1) from the EVAP canister port (2) by pinching both sides of the hose connector.



17. Remove the 4 bolts (4) and the 2 fuel tank straps from the vehicle.
18. Lower the fuel tank from the vehicle.

1. Raise the fuel tank (5) to the vehicle underbody.
2. Install the 2 fuel tank straps to the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Secure the fuel tank straps with the 4 bolts (4).

Tighten
Tighten the bolts to 39 N·m (29 lb ft).

4. Install the fuel limiter vent valve hose to the EVAP canister.
5. Install the fuel filler hose (2) to the fuel tank (5).
6. Install the fuel breather hose (3) to the fuel tank.
7. Install the ORVR hose (1) to the fuel filler pipe assembly.
8. Secure the parking brake cables to the underbody with the 4 bolts.

Tighten
Tighten the bolts to 6 N·m (53 lb in).




9. Install the rear exhaust heat shield (1) to the vehicle underbody with the 4 screws and the one nut.
10. Install the catalytic converter and intermediate pipe assembly (2) to the vehicle. Refer to Catalytic Converter Replacement in Engine Exhaust.
11. Lower the vehicle.



12. Connect the electrical connector (1) to the fuel sender assembly .



13. Connect the fuel line (2) to the fuel sender assembly.
14. Install the retaining clip (1) to the fuel line connection.



15. Inspect the butyl caulk seal for the fuel sender assembly access panel (1). Replace any missing butyl caulk as necessary.
16. Install the sender assembly access panel (1) to the rear floor.
17. Install the rear seat bottom cushion to vehicle. Refer to Rear Seat Cushion Replacement in Seats.
18. Refill the fuel tank.
19. Connect the negative battery cable.
20. Pressurize the fuel system and check for any fuel leaks.