Circuit Description
The 3-4, 4-5 shift solenoid (SS) valve (S4) controls transmission fluid pressure acting on the U1 shift valve to position the valve for the appropriate gear. The 3-4, 4-5 SS valve (S4) is a normally open exhaust valve located on the front control valve body. The solenoid is case grounded. The output driver module (ODM), within the transmission control module (TCM), commands the solenoid ON or OFF by providing voltage. When the 3-4, 4-5 SS valve (S4) is commanded ON, the TCM senses high voltage. When the 3-4, 4-5 SS valve (S4) is commanded OFF, the TCM senses low voltage.
If the TCM detects a continuous open or short to voltage in the 3-4, 4-5 SS valve (S4) circuit, then DTC P0983 sets. DTC P0983 is a type A DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0983 Shift Solenoid (SS) 4 Control Circuit High Voltage
Conditions for Running the DTC
| • | The system voltage is 10.2-15.5 volts. |
| • | The engine speed is greater than 400 RPM. |
| • | Trans. Protection Mode is OFF. |
| • | The TCM commands the solenoid OFF. |
Conditions for Setting the DTC
The 3-4, 4-5 SS valve (S4) feedback circuit indicates a continuous open or short to voltage for 0.5 second.
Action Taken When the DTC Sets
| • | The TCM requests the powertrain control module (PCM) to illuminate the malfunction indicator lamp (MIL). |
| • | The TCM turns the Trans. Protection Mode ON. |
| • | The transmission will operate in 5th gear when the transmission is shifted into D range and 2nd gear when shifted into L range. |
| • | The line pressure is at maximum. |
| • | The torque converter clutch (TCC) is disabled. |
| • | The TCM freezes the transmission adaptive functions. |
| • | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records. |
| • | The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as a Failure Record. |
| • | The TCM stores DTC P0983 in TCM history. |
Conditions for Clearing the MIL/DTC
| • | The PCM turns off the MIL after the third consecutive drive trip in which the TCM does not send a MIL illumination request. |
| • | A scan tool can clear the MIL/DTC. |
| • | The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring. |
| • | The TCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the TCM. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Yes | No |
|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 |
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Eng./Trans. DTC Info function erases the Freeze Frame and Failure Records from the transmission control module (TCM). Does the Shift Solenoid 4 CKT Status display OK? | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 3 |
3 |
Does the test lamp turn ON and OFF? | Go to Step 4 | Go to Step 7 |
4 | Inspect for poor connections at the transmission AT inline 14-way connector. Refer to Testing for Intermittent Conditions and Poor Connections . Did you find and correct the condition? | Go to Step 12 | Go to Step 5 |
Did you find and correct the condition? | Go to Step 12 | Go to Step 6 | |
6 |
Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 10 |
7 |
Refer to Circuit Testing and Wiring Repairs . Did you find the condition? | Go to Step 12 | Go to Step 8 |
8 | Inspect the TCM C2 connector for poor connections. Refer to Testing for Intermittent Conditions and Poor Connections . Did you find and correct the condition? | Go to Step 12 | Go to Step 11 |
9 | Replace the automatic transmission wiring harness. Did you complete the replacement? | Go to Step 12 | -- |
10 | Replace the 3-4, 4-5 SS valve (S4). Did you complete the replacement? | Go to Step 12 | -- |
11 | Replace the TCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 12 | -- |
12 | Perform the following procedure in order to verify the repair:
Does the DTC reset? | Go to Step 2 | Go to Step 13 |
13 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | System OK |
