GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provide an overview of each diagnostic category.

DTC Descriptors

DTC P0134: HO2S Circuit Insufficient Activity Sensor 1

DTC P0140: HO2S Circuit Insufficient Activity Sensor 2

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

HO2S 1 Signal

P0131, P0137

P0134, P0140

P0132, P0138

P0133, P1133, P1134

Low Reference

--

P0134, P0140

P0132, P0138

P0133, P1133, P1134

Typical Scan Tool Data

HO2S 1 and 2

Circuit

Short to Ground

Open

Short to Voltage

Operating Conditions: Engine operating in Closed Loop.

Parameter Normal Range: Fluctuates above and below 350-500 mV.

HO2S Signal

0 mV

400-415 mV

1000 mV

Low Reference

--

400-415 mV

1000 mV

Circuit Description

The heated oxygen sensors (HO2S) are used for fuel control and catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content of the exhaust stream. When the engine is started, the control module operates in an Open Loop mode, ignoring the HO2S signal voltage while calculating the air-to-fuel ratio. The control module supplies the HO2S with a reference, or bias voltage of about 450 mV. While the engine runs, the HO2S heats up and begins to generate a voltage within a range of 0-1,000 mV. This voltage will fluctuate above and below the bias voltage. Once sufficient HO2S voltage fluctuation is observed by the control module, Closed Loop is entered. The control module uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases above bias voltage toward 1,000 mV indicates a rich fuel mixture. An HO2S voltage that decreases below bias voltage toward 0 mV indicates a lean fuel mixture.

The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed Loop earlier and the control module to calculate the air-to-fuel ratio sooner.

The HO2S utilizes the following circuits:

    • A signal circuit
    • A low reference circuit
    • An ignition 1 voltage circuit
    • A heater control circuit

Conditions for Running the DTC

P0134

    • DTCs P0107, P0108, P0117, P0118, P0122, P0123, P0171, P0172, P0201, P0202, P0203, P0204, P0300, P0336, P0337, P0351, P0352, P0401, P0402, P0404, P0405, P0406, P042E, P0443, P0502, P0506, and P0507 are not set.
    • The startup engine coolant temperature is greater than 60°C (140°F).
    • The ignition 1 voltage is greater than 10 volts.
    • The engine airflow is more than 9 g/s.
    • The DTC runs continuously when the above conditions are met for 3 seconds after exiting decel fuel cut off (DFCO).

P0140

    • DTCs P0107, P0108, P0117, P0118, P0122, P0123, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0300, P0336, P0337, P0351, P0352, P0401, P0402, P0404, P0405, P0406, P042E, P0443, P0502, P0506, and P0507 are not set.
    • The startup engine coolant temperature is greater than 60°C (140°F).
    • The ignition 1 voltage is greater than 10 volts.
    • The engine airflow is more than 9 g/s.
    • The engine has been operating for more than 1 minute.
    • The fuel system is in closed loop.
    • The DTC runs continuously when the above conditions are met for 3 seconds after exiting DFCO.

Conditions for Setting the DTC

P0134

The ECM detects that the HO2S 1 voltage is stuck between 300 and 600 mV.

P0140

The ECM detects that the HO2S 2 voltage is stuck between 422 and 478 mV.

Action Taken when the DTC Sets

DTC  P0134 is a Type A DTC. DTC  P0140 is a Type B DTC.

Conditions for Clearing the MIL/DTC

DTC  P0134 is a Type A DTC. DTC  P0140 is a Type B DTC.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

    •  Engine Control Module Connector End Views
    •  Engine Controls Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions
    •  Scan Tool Output Controls

Circuit/System Verification

  1. Engine running, observe the appropriate scan tool heated oxygen sensor (HO2S) voltage parameter. The reading should fluctuate above and below the range of 350-550 mV.
  2. If the vehicle passes the Circuit/System Verification test, then operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector of the appropriate HO2S.
  2. Engine running, verify the appropriate scan tool HO2S parameter is between 350-500 mV.
  3. If less than the specified range, test the signal circuit for a short to ground. If the circuit/connections test normal, replace the engine control module (ECM).
    If greater than the specified range, test the signal circuit for a short to voltage. If the circuit/connections test normal, replace the ECM.

    Important: The test lamp is used to load the circuit and may not illuminate.

  4. Connect a test lamp between the low reference circuit and B+.
  5. Engine running, test for less than 0.1 volts between the low reference circuit and ground.
  6. If greater than the specified range, test the low reference circuit for a short to voltage or an open/high resistance. If the circuit/connections test normal, replace the ECM.
  7. Install a 3A fused jumper wire between the signal circuit and the low reference circuit. Verify the appropriate scan tool HO2S parameter is less than 60 mV.
  8. If greater than the specified range, test the signal circuit for an open/high resistance. If the circuit/connections test normal, replace the ECM.
  9. Verify that none of the following conditions exist:
  10. • Lean or rich fuel injectors--Refer to Fuel Injector Balance Test with Special Tool .
    • Water intrusion in the HO2S harness connector
    • Low or high fuel system pressure--Refer to Fuel System Diagnosis .
    • Fuel that is contaminated--Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Fuel saturation of the evaporative emission (EVAP) canister
    • Exhaust leaks near the HO2S
    • Engine vacuum leaks
         ⇒If you find any of the above conditions, repair as necessary.
  11. If all circuits/connections test normal, replace the appropriate HO2S.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Heated Oxygen Sensor 1 Replacement
    •  Heated Oxygen Sensor 2 Replacement
    •  Control Module References for replacement, setup, and programming