GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The engine control module (ECM) monitors the temperature of the engine coolant for engine control and as an enabling criteria for some diagnostics. The amount of air flow into an engine is proportional to the amount of heat an engine generates. The ECM monitors the amount of air flow into the engine to calculate engine coolant temperature (ECT). The ECM uses the calculated temperature to determine if the engine has warmed up to the thermostat regulating temperature. If the coolant temperature does not increase normally or does not reach regulating temperature of the thermostat, diagnostics that use the ECT as enabling criteria, may not run when expected. If the engine coolant temperature fails to reach the thermostat regulating temperature, before a predetermined amount of air flow enters the engine, this DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0128 Engine Coolant Temperature (ECT) Below Thermostat Regulating Temperature

Conditions for Running the DTC

    • DTCs P0117, P0118, P0122, P0123, P0502, P0562, P0563, P0606, and U0101 are not set.
    • The engine is operating.
    • The start-up intake air temperature is more than -39°C (-38°F).
    • Before the ECM can report DTC P0128 failed, the engine must be idling for more than a predetermined amount of time which is based off of start-up coolant temperature or start-up intake air temperature.
    • Before the ECM can report DTC P0128 failed, the airflow into the engine must be more than a predetermined amount which is based off of start-up coolant temperature or start-up intake air temperature.
    • DTC P0128 runs once an ignition cycle once the above conditions are met.

Conditions for Setting the DTC

The actual ECT is not within 10°C (50°F) of the calculated ECT after 2-5 minutes, which depends on the amount of air flow into the engine after start-up.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

    • Use the J 35616 Connector Test Adapter Kit for any test that requires probing the ECM harness connector or a component harness connector.
    • For an intermittent condition, refer to Intermittent Conditions .

Test Description

The numbers below refer to the step numbers in the diagnostic table.

  1. This step tests for excessive resistance in the ECT circuit.

  2. This step isolates the condition. If the temperature changes, test for a condition in the low reference circuit. If the temperature remains the same test the signal circuit for a condition.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check - Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Is the engine cooling system low on coolant?

--

Go to Loss of Coolant in Engine Cooling

Go to Step 3

3

Is the customer's concern that the engine does not reach operating temperature or that the heater output is low?

--

Go to Thermostat Diagnosis in Engine Cooling

Go to Step 4

4

Important: Return to this diagnostic procedure after you complete the thermostat diagnosis.

Test for the correct operation of the thermostat. Refer to Thermostat Diagnosis in Engine Cooling.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 5

5

  1. Turn OFF the ignition.
  2. Disconnect the engine coolant temperature (ECT) sensor.
  3. Connect a 3-amp fused jumper wire between the signal circuit and the low reference circuit of the ECT sensor.
  4. Turn ON the ignition, with the engine OFF.
  5. Observe the ECT sensor parameter with a scan tool.

Is the temperature more than the specified value?

214°C (417°F)

Go to Step 9

Go to Step 6

6

  1. Connect a 3-amp fused jumper between the signal circuit of the ECT sensor and the engine control module (ECM) housing.
  2. Observe the ECT sensor parameter with a scan tool.

Is the temperature more than the specified value?

214°C (417°F)

Go to Step 7

Go to Step 8

7

Test the low reference circuit of the ECT sensor for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 10

8

Test the signal circuit of the ECT sensor for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 10

9

Test for shorted terminals and poor connections at the ECT sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 11

10

Test for shorted terminals and poor connections at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 13

Go to Step 12

11

Replace the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement .

Did you complete the replacement?

--

Go to Step 13

--

12

Replace the ECM. Refer to Engine Control Module Replacement .

Did you complete the replacement?

--

Go to Step 13

--

13

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 14

14

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK