GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The knock sensor (KS) enables the engine control module (ECM) to control the ignition timing for the best possible performance while protecting the engine from potentially damaging levels of detonation. The KS produces an AC voltage signal that varies depending on the vibration level during engine operation. The ECM adjusts the spark timing based on the amplitude and the frequency of the KS signal. The ECM receives the KS signal through a signal circuit . The ECM supples a ground circuit to the KS through a low reference circuit . The ECM also supplies a shielded ground circuit to the KS. The ECM learns a KS noise level at idle and uses calibrated values for the rest of the RPM range. The ECM should monitor a normal KS signal within the noise channel. The circuits between the KS sensor and the ECM consists of the following circuits:

    • A signal
    • A low reference
    • A shielded ground

If the ECM detects the KS signal outside of the noise channel, or the KS signal is not present, this DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0327 Knock Sensor (KS) Circuit Low Frequency

Conditions for Running the DTC

    • DTCs P0106, P0107, P0108, P1106, and P1107 are not set.
    • The engine coolant temperature (ECT) is more than 50°C (122°F).
    • The engine speed is more than 1,600 RPM.
    • The manifold absolute pressure (MAP) is between 10-50 kPa.
    • DTC P0327 runs continuously once the above conditions are met.

Conditions for Setting the DTC

The ECM detects an incorrect KS signal for more than 4 seconds.

Action Taken When the DTC Sets

    • The control module stores the DTC information into memory when the diagnostic runs and fails.
    • The malfunction indicator lamp (MIL) will not illuminate.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records.
    • The driver information center, if equipped, may display a message.

Conditions for Clearing the DTC

    • A current DTC Last Test Failed clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic.
    • Clear the DTC with a scan tool.

Diagnostic Aids

    • Inspect the KS for physical damage. A KS that is dropped or damaged may cause a DTC to set.
    • Inspect the KS for proper installation. A KS that is loose or over torqued may cause a DTC to set. The KS should be free of thread sealant. The KS mounting surface should be free of burrs, casting flash, and foreign material.
    • The KS must be clear of hoses, brackets, and engine electrical wiring.
    • For an intermittent condition, refer to Intermittent Conditions .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step determines if the fault is current.

  1. This step determines if the fault is intermittent.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check - Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Important: If an engine mechanical noise can be heard, repair the condition before proceeding with this diagnostic. Refer to Symptoms - Engine Mechanical in Engine Mechanical - 1.8L - L79.

  1. Start the engine.
  2. Operate the engine within the Conditions for Running the DTC.
  3. Observe the DTC information with a scan tool.

Did DTC P0327 fail this ignition?

--

Go to Step 4

Go to Step 3

3

  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn the ignition OFF for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 4

Go to Diagnostic Aids

4

  1. Turn OFF the ignition.
  2. Disconnect the knock sensor (KS) harness connector.
  3. Measure the resistance from the signal circuit and the low reference circuit on the controller side of the KS harness connector to a good ground with the DMM.

Is the resistance within the specified range?

96K-107K ohms

Go to Step 5

Go to Step 6

5

Measure the resistance from the shielded ground circuit on the controller side of the KS harness connector to a good ground with the DMM.

Is the resistance within the specified range?

92-98 ohms

Go to Step 8

Go to Step 7

6

Test the signal circuit and the low reference circuit on the controller side of the KS for the following conditions:

    • An open
    • A short to ground
    • A short to voltage
    • High resistance
    • A short between both circuits

Refer to Testing for a Short to Voltage and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

7

Test the shielded ground circuit on the controller side of the KS for the following conditions:

    • An open
    • A short to ground
    • A high resistance
    • A short to voltage

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

8

Test for an intermittent and for a poor connection at the KS. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 10

9

Test for an intermittent and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 11

10

Replace the KS. Refer to Knock Sensor Replacement .

Did you complete the replacement?

--

Go to Step 12

--

11

Replace the ECM. Refer to Engine Control Module Replacement .

Did you complete the replacement?

--

Go to Step 12

--

12

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 13

13

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK