GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0556: Brake Booster Pressure Sensor Performance

DTC P0557: Brake Booster Pressure Sensor Circuit Low Voltage

DTC P0558: Brake Booster Pressure Sensor Circuit High Voltage

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

5-Volt Reference

P0557

P0557

P0558

P0556

Brake Booster Vacuum Sensor Signal

P0557

P0557

P0558

P0556

Low Reference

--

P0557

--

P0556

Circuit/System Description

The brake booster pressure sensor measures the negative air pressure or vacuum reserve in the brake booster assembly. During engine running conditions, the brake booster pressure sensor signal circuit voltage varies, depending on the vacuum reserve internal to the brake booster.

Conditions for Running the DTC

P0556

Engine running at idle.

P0557 or P0558

Ignition ON.

Conditions for Setting the DTC

P0556

The ECM detects brake booster vacuum as being less than the intake manifold vacuum for more than 100 milliseconds.

P0557

The ECM detects less than 0.04 volts on the brake booster sensor signal circuit for more than 12.5 milliseconds.

P0558

The ECM detects greater than 4.89 volts on the brake booster sensor signal circuit for more than 12.5 milliseconds.

Action Taken When the DTC Sets

The ECM sends a serial data message to the IPC to illuminate the MIL.

Conditions for Clearing the DTC

The conditions for the DTC are no longer present after 3 consecutive ignition cycles.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Engine Controls Connector End Views

Description and Operation

Cylinder Deactivation (Active Fuel Management) System Description

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the brake booster vacuum sensor.
  2. Ignition OFF, test for less than 5 ohms between the low reference circuit terminal 2 and ground.
  3. If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
  4. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 3 and ground.
  5. If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
    If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.
  6. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 3 and the signal circuit terminal 1.
  7. If less than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
    If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.
  8. Ignition OFF, disconnect the C1 harness connector at the ECM.
  9. Ignition OFF, test for infinite resistance between the signal circuit terminal 46 and ground.
  10. If not the specified value, test the signal circuit for a short to ground.
  11. If all circuits test normal, test or replace the power brake booster vacuum sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Power Brake Booster Vacuum Sensor Replacement
    •  Control Module References for ECM replacement, setup, and programming