The camshaft position (CMP) actuator is attached to each camshaft and is hydraulically operated in order to change the angle of the camshaft relative to crankshaft position (CKP). The CMP actuator solenoid is controlled by the control module. The control module sends a pulse width modulated 12-volt signal to a CMP actuator solenoid. The solenoid controls the amount of engine oil flow to a CMP actuator. The CMP actuator can change the camshaft angle a maximum of 25 degrees. The control module increases the pulse width to accomplish the desired camshaft operation.

The engine is running.

DTCs P0011 and P0014 are Type B DTCs.

DTCs P0011 and P0014 are Type B DTCs.

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

1. Ensure the vehicle has the proper oil viscosity.
2. Observe the engine oil level. The engine oil level should be within the operating range.
3. Allow the engine to reach operating temperature.
4. Command each CMP actuator to 25 percent. The CMP actuator angle desired parameter should match the CMP actuator actual parameter.
5. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

1. Ignition OFF, disconnect the CMP actuator solenoid harness connector at the CMP actuator solenoid.
2. Test for less than 5 ohms between the low reference circuit terminal B and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance.

3. Verify that a test lamp does not illuminate between the low reference circuit terminal B and the control circuit terminal A.

⇒	If the test lamp illuminates, test the control circuit for short to voltage. If the circuit tests normal, replace the ECM.

4. Remove the test lamp.
5. Command the CMP Actuator Sol. ON with a scan tool. Verify the scan tool CMP Sol Ckt Short Gnd Test status is OK.

⇒	If not the specified value, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.

6. Install a 3A fused jumper wire between the control circuit terminal A and the low reference circuit terminal B. Command the CMP Actuator Sol. ON with a scan tool. Verify the scan tool CMP Sol Ckt Short Gnd Test status is Fault.

⇒	If not the specified value, test the control circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

7. Determine that the vehicle has the correct engine oil. Refer to Service and Appearance Care in the owner's manual.

⇒	If the engine oil life system monitor displays the Change Oil Soon message, the engine oil is more than one year old, contains additives, or is not the correct viscosity, change the oil.

8. Test the engine oil pressure. Refer to Oil Pressure Diagnosis and Testing.

⇒	If the oil pressure is low, correct the low pressure first.

9. Inspect each CMP actuator solenoid valve assembly for the following:

•	Torn screens

•	Debris on the screens

•	Debris clogging the oil ports

•	Missing screens

•	Oil seepage at the solenoid connector pins

10. Connect a jumper wire between the CMP actuator low reference circuit terminal B at the solenoid and a good ground. Connect a fused jumper wire to the CMP actuator high control circuit terminal A at the solenoid. Momentarily touch the fused jumper to B+. Observe the spool valve inside the CMP actuator. The spool valve should move.

⇒	If movement is not observed, replace the CMP actuator solenoid.

11. Inspect the engine timing components. Refer to Camshaft Timing Chain and Sprocket Cleaning and Inspection.
12. If all circuits test normal, test or replace the CMP actuator.

1. Measure the resistance of each CMP actuator solenoid valve assembly. Resistance should be between 8-12 ohms.
2. Connect a jumper wire between the CMP actuator low reference circuit at the solenoid and a good ground. Connect a fused jumper wire to the CMP actuator high control circuit at the solenoid. Momentarily touch the fused jumper to B+. Observe the spool valve inside the CMP actuator. The spool valve should move from fully closed to fully opened position.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.