GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B3715 02:  Front Wiper Relay Drive Circuit Short to Ground

DTC B3715 05:  Front Wiper Relay Drive Circuit Short to Battery or Open

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

WPR HI Relay B+

1, 2

1, 2

--

--

Windshield Wiper Switch Signal

1

1

1

--

Windshield Wiper Switch High Signal

4

2

2

--

Windshield Wiper Motor Park Switch Signal

3

3

--

--

WPR 1 Relay Control

B3715 02

B3715 05

B3715 05

--

WPR  2 Relay Control

4

2

4

--

Windshield Wiper Motor High Speed Control

2

2

4

--

Windshield Wiper Motor Low Speed Control

1

1

4

--

Windshield Wiper Switch Low Reference

--

1, 2

1, 2

--

Windshield Wiper Motor Ground

--

1, 2, 3

--

--

WPR Relay Ground

--

1

--

--

1. Delay or Low Speed Wipers Inoperative

2. High Speed Wipers Inoperative

3. Wipers Do Not Park

4. Wipers Always ON

Circuit/System Description

The body control module (BCM) monitors the control circuit of the wiper relay. The voltage level should be low while the wiper relay is de-energized and near system voltage when the relay is energized. After the BCM receives a low, intermittent, or mist signal from the wiper/washer switch, it responds by applying battery voltage through the wiper relay control circuit to the coil side of the relay, energizing the WIPER Relay. Ground is supplied at all times to the coil side of the WIPER relay

Conditions for Running the DTC

The wiper output is actively being requested by the BCM.

Conditions for Setting the DTC

The BCM detects an open, short to ground or short to voltage in the wiper relay control circuit.

Action Taken When the DTC Sets

The BCM will not activate the wiper output.

Conditions for Clearing the DTC

    • The current DTC will become history when the request for the output is removed or when the condition for setting the fault is corrected.
    • The history DTC will clear after 50 consecutive ignition cycles without a fault present.

Reference Information

Schematic Reference

Wiper/Washer Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Wiper/Washer System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Testing

  1. Ignition OFF, disconnect the WPR relay.
  2. Connect a test lamp between the control circuit terminal  85 and ground.
  3. Ignition ON, command the low speed wipers ON and OFF using the wiper switch. The test lamp should turn ON and OFF when changing between the commanded states.
  4. If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
    If the test lamp is always OFF, test for a short to ground or an open/high resistance on the control circuit. If the circuit tests normal, replace the BCM.
  5. If all circuits test normal, test or replace the WPR relay.

Component Testing

  1. Ignition OFF, disconnect the WPR relay.
  2. Test for 60-200 ohms between terminals 85 and 86.
  3. If the resistance is not within the specified range, replace the relay.
  4. Test for infinite resistance between the following terminals:
  5. • 30 and 86
    • 30 and 87
    • 30 and 85
    • 85 and 87
    If not the specified value, replace the relay.
  6. Test for less than 2 ohms between terminals 30 and 87A.
  7. If greater than the specified range, replace the relay.
  8. Install a 10A fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms between terminals 30 and 87.
  9. If greater than the specified range, replace the relay.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for BCM replacement, setup, and programming