GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B0023 01: Right Roof Rail Deployment Loop Short to Battery

DTC B0023 02: Right Roof Rail Deployment Loop Short to Ground

DTC B0023 04: Right Roof Rail Deployment Loop Open Circuit

DTC B0023 0D: Right Roof Rail Deployment Loop Resistance Above Threshold

DTC B0023 0E: Right Roof Rail Deployment Loop Resistance Below Threshold

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

Right Roof Rail Module High Control

B0023 02

B0023 0D, B0023 04

B0023 04

B0023 01

B0023 0E

Right Roof Rail Module Low Control

B0023 02

B0023 0D, B0023 04

B0023 04

B0023 01

B0023 0E

Circuit/System Description

During a side or frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the roof rail module. A shorting bar is located in the electrical connector of the roof rail module. The roof rail module high control circuit and low control circuit are shorted together by the shorting bar when the electrical connector is disconnected. The shorting bar helps to prevent unwanted deployment of the inflator module during servicing.

The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If the result of any deployment loop circuit test is below specification, DTC B0023 and the appropriate symptom byte sets.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0023 01

The right roof rail module high and/or low circuit is short to voltage for 120 milliseconds.

B0023 02

The right roof rail module high and/or low circuit is short to ground for 120 milliseconds.

B0023 04

The right roof rail module high and/or low circuit is open for 120 milliseconds.

B0023 0D

The right roof rail module deployment loop resistance is greater than 3.9 ohms for 120 milliseconds.

B0023 0E

The right roof rail module deployment loop resistance is less than 1.1 ohms for 120 milliseconds.

Action Taken When the DTC Sets

    • The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator and display the message "Service Air Bag."
    • The SDM will store a DTC, however if an event occurs the system will still attempt deployments.

Conditions for Clearing the DTC

    • The condition for setting the DTC no longer exists.
    • A history DTC will clear once 100 malfunction-free ignition cycles have occurred.

Diagnostic Aids

If DTC B0023 0E is setting, be certain that all circuit shorting bars are isolated after connecting circuit components. There are shorting bars in most circuit connectors, including the SDM and inline harness connectors. DTC B0023 0E will set if the shorting bars are engaged when the ignition is ON.

Reference Information

Schematic Reference

SIR Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

SIR System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Special Tools

Each inflatable restraint module requires a specific adapter to connect the load tool to the SIR system.

    • J 38715-A Driver and Passenger SIR Load Tool
    • SA9409Z-A SIR Load Tool (Driver/Passenger/Curtain)

Circuit/System Testing

Important: Refer to SIR Service Precautions.

When removing the connectors, inspect for terminal damage or corrosion. Inspect the connector body for damage to the locators that disengage the shorting bars when connected. Damage or corrosion to the following components requires repair or replacement of the affected component/connector:

   • Inflatable restraint module
   • SDM module
   • Front end sensor wiring harness connector
   • SDM wiring harness connector

Important: The connector and connector position assurance (CPA) may seat independent of each other. Both the connector and CPA should seat with an audible and/or tactile click. Correct connection isolates the shorting-bars within the connector allowing the deployment circuit to operate properly.

  1. Verify that the inflatable restraint right roof rail module connector and CPA are engaged.
  2. If the above condition is not found, make the appropriate repair.
  3. Ignition OFF, disconnect the harness connector at the right roof rail module.
  4. With the appropriate load tool adapter, connect J 38715-A or SA9409Z-A in place of the right roof rail module.
  5. Ignition ON, with a scan tool, verify that DTC B0023 is set as current.
  6. If the DTC is not set or is set as history, cycle the ignition OFF, disconnect the load tool and adapter, reconnect the harness connector at the right roof rail module, and cycle the ignition ON. If the DTC resets after reconnecting the module, replace the right roof rail module.
  7. Ignition OFF, disconnect the load tool and the adapter.
  8. Disconnect the harness connector at the SDM.
  9. Ignition ON, test for less than 1.0 volt between the appropriate control circuit listed below and ground:
  10. • Control circuit terminal 10
    • Control circuit terminal 11
    If not within the specified range, test the control circuit for a short to voltage.
  11. Ignition OFF, test for infinite resistance between the appropriate control circuit listed below and ground:
  12. • Control circuit terminal 10
    • Control circuit terminal 11
    If not within the specified value, test the control circuit for a short to ground.
  13. Test for less than 1 ohm between the appropriate control circuit terminal and SDM terminal listed below:
  14. • Control circuit terminal A and SDM terminal 11
    • Control circuit terminal B and SDM terminal 10
    If not within the specified range, test the control circuit for an open/high resistance.
  15. If all circuits test normal, replace the SDM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Inflatable Restraint Roof Side Rail Module Replacement
    •  SIR/SRS Wiring Repairs
    •  Control Module References for SDM replacement, setup, and programming