GM Service Manual Online
For 1990-2009 cars only

Disassembly Procedure

    Warning: Refer to Brake Dust Warning in the Preface section.

    Warning: Refer to Brake Fluid Irritant Warning in the Preface section.


    Object Number: 773687  Size: SH
  1. Remove the brake caliper from the vehicle. Refer to Front Brake Caliper Replacement.
  2. Warning: Do not place fingers in front of the caliper piston(s) in an attempt to catch or protect it when applying compressed air. The piston(s) can fly out with force and could result in serious bodily injury.

    Caution: Use clean cloths to pad interior of caliper housing during piston removal. Use just enough air to ease the pistons out of the bores. If the pistons are blown out, even with the padding provided, it may be damaged.

  3. Remove the brake caliper piston from the caliper bore by directing low pressure compressed air into the caliper bore through the fluid inlet hole.

  4. Object Number: 777640  Size: SH
  5. Remove the retaining ring that secures the dust boot to the caliper housing.

  6. Object Number: 1212583  Size: SH
  7. Remove the piston dust boot seal (2) from the seal counterbore in the caliper (5). Discard the boot seal.
  8. Using a small wooden or plastic tool, remove the piston seal (4) from the caliper bore. Discard the piston seal.
  9. Remove the bleeder valve cap (6).
  10. Remove the bleeder valve (7).
  11. Note: Do not use abrasives to clean the brake caliper piston.

  12. If cracks, scoring, pitting, excessive rust, and/or excessive corrosion are present in the caliper bore, replace the caliper assembly.
  13. If light rust or light corrosion are present in the caliper bore, attempt to remove the imperfection with a fine emery paper. If the imperfection cannot be removed, replace the caliper assembly.
  14. Clean the brake caliper piston bore and seal counterbore, and the caliper piston with denatured alcohol, or equivalent.
  15. Dry the caliper piston bore and counterbore, and the piston with non-lubricated, filtered, compressed air.
  16. Inspect the caliper piston for cracks, scoring, and/or damage to the plating. Replace the caliper piston if any of these conditions exist.
  17. Inspect the caliper mounting holes for cracks, scoring, pitting, rust and/or excessive corrosion. Replace the caliper assembly if any of these conditions exist.

Assembly Procedure


    Object Number: 1212583  Size: SH
  1. Lubricate the new piston seal (4) with Delco Supreme 11 GM P/N 12377967 (Canadian P/N 992667), or equivalent DOT-3 brake fluid from a clean, sealed brake fluid container.
  2. Install the lubricated, new piston seal (4) into the caliper bore.
  3. Apply a thin coat of Delco Supreme 11 GM P/N 12377967 (Canadian P/N 992667), or equivalent DOT-3 brake fluid from a clean, sealed brake fluid container onto the outer surface area of the caliper piston (3).

  4. Object Number: 777638  Size: SH
  5. Install the bottom half of the caliper piston (2) into the caliper bore.
  6. Install the new piston dust boot seal (1) over the caliper piston (2).
  7. Compress the caliper piston (2) to the bottom of the caliper bore.
  8. Fully seat the piston dust boot seal (1) into caliper counterbore.

  9. Object Number: 777640  Size: SH
  10. Install the retaining ring that secures the dust boot to the caliper housing.
  11. Caution: Refer to Fastener Caution in the Preface section.

  12. Install the bleeder valve to the caliper and tighten the valve to 11 N·m (97 lb in).
  13. Install the bleeder valve cap.
  14. Install the brake caliper to the vehicle. Refer to Front Brake Caliper Replacement.