Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC P0722: Output Speed Sensor (OSS) Circuit Low VoltageDTC P0723: Output Speed Sensor (OSS) Intermittent
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
OSS Supply Voltage | P0722 | P0722 | -- | -- |
OSS Signal | P0722, P0723 | P0722, P0723 | P0722, P0723 | -- |
Typical Scan Tool Data
Circuit | Short to Ground | Open/High Resistance | Short to Voltage |
|---|---|---|---|
Operating Conditions: Engine running, normal operating temperature Parameter Normal Range: 0-7,000 RPM | |||
ISS/OSS Supply Voltage (Pin B) | Out of Range | Out of Range | OK |
Transmission OSS (Pin C) | 0 RPM | 0 RPM | 0 RPM |
Circuit/System Description
The output speed sensor (OSS) is a hall-effect type sensor. The sensor faces the output shaft machined teeth surface. The sensor receives 8.3-9.3 volts on the input/output speed sensor (ISS/OSS) supply voltage circuit from the transmission control module (TCM). As the output shaft rotates, the sensor produces a signal frequency based on the machined surface of the output shaft. This signal is transmitted through the OSS signal circuit to the TCM. The TCM uses the OSS signal to determine line pressure, transmission shift patterns, torque converter clutch (TCC) slip speed and gear ratio.
Conditions for Running the DTC
P0722
| • | No ISS DTCs P0716 or P0717. |
| • | No OSS DTC P0723. |
| • | The selected range is not PARK or NEUTRAL. |
| • | The vehicle speed is greater than 16 km/h (10 mph). |
| • | The transmission input speed is between 1,000-6,500 RPM. |
| • | The engine speed is between 3,000-5,000 RPM. |
| • | The calc. throttle position is greater than 8 percent. |
| • | The engine torque is greater than 50 N·m (37 lb ft). |
| • | The TFT is greater than 0°C (32°F). |
| • | The engine speed is greater than 500 RPM for 5 seconds. |
| • | The ignition voltage is between 8.6 volts and 19.0 volts. |
P0723
| • | No ISS DTCs P0716 or P0717. |
| • | No OSS DTC P0722. |
| • | Greater than 6 seconds since last range change. |
| • | DTC P0723 has not passed this ignition cycle. |
| • | The engine speed is greater than 500 RPM for 5 seconds. |
| • | The ignition voltage is between 8.6 volts and 19.0 volts. |
Conditions for Setting the DTC
P0722
The transmission output speed is 70 RPM or less for 4.5 seconds.
P0723
| • | The transmission input speed does not change by more than 500 RPM for 2 seconds. |
| • | The transmission output speed is 1,000 RPM or greater for 2 seconds. |
| • | The transmission output speed drops 1,200 RPM for greater than 1.5 seconds and does not recover. |
Action Taken When the DTC Sets
| • | DTCs P0722 and P0723 are Type A DTCs. |
| • | The TCM freezes transmission adaptive functions. |
| • | The TCM turns OFF all solenoids. |
Conditions for Clearing the DIC/DTC
DTCs P0722 and P0723 are Type A DTCs.
Diagnostic Aids
| • | Damage or misalignment of the 3-5-R clutch piston housing machined teeth surface may cause a speed sensor malfunction. |
| • | Proper torque of the OSS mounting bolt is critical to proper OSS operation. |
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics
Connector End View Reference
Description and Operation
Electronic Component Description for output speed sensor (OSS)
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Special Tools
J 38522 Variable Signal Generator
Circuit/System Verification
- Operate the vehicle at 16-32 km/h (10-20 mph) while observing the scan tool transmission OSS parameter. The transmission OSS should vary with the vehicle speed and not drop out.
- Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observes from the Freeze Frame/Failure Records data.
Circuit/System Testing
- Ignition OFF, remove the control valve body cover. Refer to Control Valve Body Cover Replacement.
- Connect the TCM harness connector.
- Disconnect the output speed sensor (OSS) harness connector from the control solenoid (w/body and TCM) valve assembly.
- Connect the J 38522 between the supply voltage terminal B and ISS signal terminal C at the control solenoid (w/body and TCM) valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly Input Shaft Speed/Output Shaft Speed Input Test for further instructions.
- Set the J 38522 signal to 8 volts, the frequency to 120 and the percent duty cycle to 50.
- Ignition ON, observe the scan tool Transmission OSS parameter. The scan tool Transmission OSS parameter should be between 100-400 RPM.
- If all circuits test normal, test or replace the output speed sensor.
| ⇒ | If not within the specified range, replace the control solenoid (w/body and TCM) valve assembly. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| Important: Perform the Service Fast Learn Adapts following all transmission related repairs. |
| Important: Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection. |
| • | Control Module References for control solenoid (w/body and TCM) valve assembly replacement, setup, and programming |
