GM Service Manual Online
For 1990-2009 cars only

Catalytic Converter Replacement - Right Side LY7

Removal Procedure

    Warning: Refer to Exhaust Service Warning in the Preface section.

    Warning: Refer to Protective Goggles and Glove Warning in the Preface section.


    Object Number: 1840274  Size: SH
  1. Remove the exhaust manifold heat shield. Refer to Exhaust Manifold Heat Shield Replacement - Right Side.
  2. Remove the catalytic converter to exhaust manifold nuts (1).
  3. Remove the bank 1 sensor 2 heated oxygen sensor (HO2S). Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 2.

  4. Object Number: 1840317  Size: SH
  5. Remove the left catalytic converter (3) to right catalytic converter (1) nuts (2).

  6. Object Number: 1586013  Size: SH
  7. Remove the exhaust pipe to right catalytic converter nuts.

  8. Object Number: 1840348  Size: SH
  9. Remove the catalytic converter from the vehicle.
  10. Remove and discard the catalytic converter to exhaust manifold gasket (1).
  11. Remove and discard the left catalytic converter to right catalytic converter gasket (2).

Installation Procedure


    Object Number: 1840348  Size: SH
  1. Install a NEW catalytic converter to exhaust manifold gasket (1) onto the catalytic converter.
  2. Install the catalytic converter to the vehicle.
  3. Install a NEW left catalytic converter to right catalytic converter gasket (2) between the converters.
  4. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1840317  Size: SH
  5. Install the left catalytic converter to right catalytic converter nuts and tighten to 25 N·m (18 lb ft).

  6. Object Number: 1586013  Size: SH
  7. Install the exhaust pipe to right catalytic converter nuts and tighten to 25 N·m (18 lb ft).
  8. Install the bank 1 sensor 2 HO2S. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 2.

  9. Object Number: 1840274  Size: SH
  10. Install the catalytic converter to exhaust manifold nuts (1) and tighten to 45 N·m (33 lb ft).
  11. Install the exhaust manifold heat shield. Refer to Exhaust Manifold Heat Shield Replacement - Right Side.

Catalytic Converter Replacement - Right Side LZ4

Special Tools

J 39194-B Heated Oxygen Sensor Wrench

Removal Procedure

Caution: The oxygen sensor uses a permanently attached pigtail and connector. Do not remove the pigtail from the oxygen sensor. Damage to or removal of the pigtail connector could affect proper operation of the oxygen sensor.

Caution: The use of excessive force may damage the threads in the exhaust manifold/pipe.

Note: The in-line connector and louvered end must be kept clear of grease, dirt or other contaminants. Avoid using cleaning solvents of any type. DO NOT drop or roughly handle the HO2S.

Note: The HO2S may be difficult to remove when the engine temperature is less than 48°C (120°F).


    Object Number: 1777682  Size: SH
  1. Remove the muffler assembly. Refer to Exhaust Muffler Replacement.
  2. Remove the rear stabilizer shaft. Refer to Stabilizer Shaft Replacement.
  3. Remove the connector position assurance (CPA) retainer (3).
  4. Disconnect the lower right heated oxygen sensor (HO2S) electrical connector from the engine wiring harness electrical connector (2).

  5. Object Number: 1492088  Size: SH
  6. Remove the lower right HO2S (2) using the J 39194-B .

  7. Object Number: 1684169  Size: SH
  8. Remove the left (front) catalytic converter to right (rear) catalytic converter nuts (3).
  9. Remove the right (rear) catalytic converter bolt (5) and nuts (1) at the exhaust manifold.
  10. Remove the right catalytic converter (2).
  11. Remove and discard the gasket (6).
  12. Inspect the catalytic converter-to-exhaust manifold flange.
  13. Catalytic Converter to Manifold Flange Warpage:

        • Service Limit: 0.7 mm (0.028 in) max.
        • Standard: 0.7 mm (0.028 in) max.

Installation Procedure


    Object Number: 1684169  Size: SH
  1. Install a NEW gasket (6) to the catalytic converter.
  2. Install the right (rear) catalytic converter (2).
  3. Caution: Refer to Fastener Caution in the Preface section.

  4. Install the right (rear) catalytic converter bolt (5) and nuts (1) at the exhaust manifold and tighten to 45 N·m (33 lb ft).
  5. Install the left (front) catalytic converter to right (rear) catalytic converter nuts (3) and tighten to 25 N·m (18 lb ft).

  6. Object Number: 1492088  Size: SH

    Note: A special anti-seize compound is used on the HO2S threads. The compound consists of graphite suspended in fluid and glass beads. The graphite will burn away, but the glass beads will remain, making the sensor easier to remove. New or service sensors will already have the compound applied to the threads. If a sensor is removed from an engine and is to be reinstalled, the threads must have anti-seize compound applied before the reinstallation.

  7. If reinstalling the old HO2S, coat the threads with anti-seize compound GM P/N 12377953 or equivalent.
  8. Install the lower right HO2S (2) using the J 39194-B . Tighten the sensor to 42 N·m (31 lb ft).

  9. Object Number: 1777682  Size: SH
  10. Connect the lower right HO2S electrical connector to the engine wiring harness electrical connector (2).
  11. Install the CPA retainer (3).
  12. Install the rear stabilizer shaft. Refer to Stabilizer Shaft Replacement.
  13. Install the muffler assembly. Refer to Exhaust Muffler Replacement.