GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 38185 Hose Clamp Pliers

Removal Procedure


    Object Number: 1892160  Size: SH
  1. Disconnect the hybrid battery. Refer to Hybrid Battery Service Disconnect/Connect .
  2. Drain the cooling system. Refer to Cooling System Draining and Filling .
  3. Remove the battery tray. Refer to Battery Tray Replacement .
  4. Reposition the power brake booster vacuum hose (2) clamp at the intake manifold.
  5. Remove the power brake booster vacuum hose from the intake manifold.
  6. Remove the power brake booster vacuum hose from the clamp (2) on the generator control module coolant outlet hose.
  7. Reposition the power brake booster vacuum hose out of the way.

  8. Object Number: 1891759  Size: SH

    Caution: To help avoid personal injury, additional precautions must be taken prior to working on the generator control module or the generator starter. After removing the 36V battery cables from the generator battery, remove both engine wiring harness connectors from the generator control module. Wait at least 5 minutes and then remove the generator control module cover. Verify voltage levels at all 36V, 12V, and 3-phase connections, are less than 3 volts using a DMM before proceeding.

  9. Remove the 2 connector position assurance (CPA) retainers (3).
  10. Disconnect the 2 engine wiring harness electrical connectors (2) from the generator control module.
  11. WAIT at least 5 minutes in order to allow the voltage stored in the generator control module to discharge.

  12. Object Number: 1891960  Size: SH
  13. Remove the generator control module bracket reinforcement bolt (1) and nuts (2).
  14. Remove the generator control module bracket reinforcement (3).

  15. Object Number: 1891970  Size: SH
  16. Reposition the generator control module coolant inlet hose clamp (1) at the generator control module using the J 38185 or equivalent.
  17. Remove the generator control module coolant inlet hose (2) from the generator control module.

  18. Object Number: 1892174  Size: SH
  19. Reposition the generator control module coolant outlet hose clamp (1) at the generator control module using the J 38185 or equivalent.
  20. Remove the generator control module coolant outlet hose (2) from the generator control module.

  21. Object Number: 1891961  Size: SH
  22. Loosen the generator control module cover integral bolts (1) and remove the cover (2).

  23. Object Number: 1891958  Size: SH
  24. The generator control module will have to be checked for voltage potential using a voltmeter. First, verify that the voltmeter works:
  25. 18.1. Set the voltmeter to DC voltage.
    18.2. Measure the vehicle 12-volt battery voltage.
    18.3. The meter should read greater than +12 volts DC.
  26. Check the generator control module for voltage potential, in order to ensure that the module has been disabled.
  27. 19.1. Measure from the 36-volt positive terminal (3) to a known good chassis ground. The voltage should be less than 3 volts.
    19.2. Measure from the 12-volt positive terminal (2) to a known good chassis ground. The voltage should be less than 3 volts.
    19.3. Measure from the ground terminal (4) to a known good chassis ground, checking for continuity.

    Caution: To help avoid personal injury, always treat the 3-phase cable and connectors as if voltage is present and as if the surface of all parts of the cable is hot.

  28. Verify that the generator control module 3-phase cables are disabled.
  29. 20.1. Measure from each phase 1, 2, and 3 connection (1) to a known good chassis ground. The voltage should be less than 3 volts.
    20.2. After verifying that there is no voltage present, the generator control module 3-phase cables can now be removed from the generator control module.

    Object Number: 1891966  Size: SH
  30. Remove the 36-volt terminal block nuts (1) from the generator control module.
  31. Lift up, and reposition the 36-volt terminal block (2), secure the block out of the way. Discard the terminal block seal.

  32. Object Number: 1891965  Size: SH
  33. Remove the generator control module 3-phase cable terminal block nuts (1) from the generator control module.
  34. Lift up, and reposition the generator control module 3-phase cable terminal block (2), secure the block out of the way. Discard the terminal block seal.

  35. Object Number: 1891759  Size: SH
  36. Disconnect the engine wiring harness electrical connector (1) from the transaxle auxiliary pump module.

  37. Object Number: 1892175  Size: SH
  38. Remove the generator control module ground strap nut (1) and strap (2) from the module stud.

  39. Object Number: 1892187  Size: SH
  40. Remove the engine wiring harness clips (1) from the battery tray bracket studs.

  41. Object Number: 1892176  Size: SH
  42. Remove the generator control module nuts (1).
  43. Remove the generator control module (with bracket) (2) from the vehicle.

  44. Object Number: 1892177  Size: SH
  45. Place the generator control module assembly on a clean work surface.
  46. Remove the generator control module bracket to module bolts (2). Separate the generator control module (1) from the bracket (3).
  47. If replacing the generator control module. remove the transaxle auxiliary pump control module. Refer to Auxiliary Fluid Pump Control Module Replacement .

Installation Procedure


    Object Number: 1892177  Size: SH
  1. If the generator control module was replaced. install the transaxle auxiliary pump control module. Refer to Auxiliary Fluid Pump Control Module Replacement .
  2. Notice: Refer to Fastener Notice in the Preface section.

  3. Position the generator control module (1) to the bracket (3), and install the generator control module bracket to module bolts (2).
  4. Tighten
    Tighten the bolts to 10 N·m (89 lb in).


    Object Number: 1892176  Size: SH
  5. Install the generator control module (with bracket) (2) to the vehicle.
  6. Install the generator control module bracket nuts.
  7. Tighten
    Tighten the nuts to 10 N·m (89 lb in).


    Object Number: 1892175  Size: SH
  8. Install the generator control module ground strap (2) to the stud and install the ground strap nut (1) to the module.
  9. Tighten
    Tighten the nut to 10 N·m (89 lb in).


    Object Number: 1891759  Size: SH
  10. Connect the engine wiring harness electrical connector (1) to the transaxle auxiliary pump.

  11. Object Number: 1891965  Size: SH
  12. Place a NEW terminal block seal onto the generator control module.
  13. Install the generator control module 3-phase cable terminal block (2) onto the generator control module.
  14. Install the generator control module 3-phase cable terminal block nuts (1) until snug.

  15. Object Number: 1891968  Size: SH
  16. Tighten the generator control module 3-phase cable terminal block nuts in the sequence shown.
  17. Tighten
    Tighten the nuts to 8 N·m (71 lb in).


    Object Number: 1891966  Size: SH
  18. Place a NEW terminal block seal onto the generator control module.
  19. Unsecure, and position the 36-volt terminal block (2) to the generator control module.
  20. Install the 36-volt terminal block nuts (1) to the generator control module.
  21. Tighten
    Tighten the nuts to 10 N·m (89 lb in).


    Object Number: 1891961  Size: SH
  22. Place the generator control module cover (2) on top of the generator control module and tighten bolts (1).
  23. Tighten
    Tighten the bolts to 10 N·m (89 lb in).


    Object Number: 1892174  Size: SH
  24. Install the generator control module coolant outlet hose (2) to the generator control module.
  25. Position the generator control module coolant outlet hose clamp (1) at the generator control module using the J 38185 or equivalent.

  26. Object Number: 1891970  Size: SH
  27. Install the generator control module coolant inlet hose (2) to the generator control module.
  28. Position the generator control module coolant inlet hose clamp (1) at the generator control module using the J 38185 or equivalent.

  29. Object Number: 1891960  Size: SH
  30. Install the generator control module bracket reinforcement (3).
  31. Install the generator control module bracket reinforcement bolt (1) and nuts (2).
  32. Tighten
    Tighten the bolt/nuts to 10 N·m (89 lb in).


    Object Number: 1891759  Size: SH
  33. Connect the 2 engine wiring harness electrical connectors (2) to the generator control module.
  34. Install the 2 CPA retainers (3).

  35. Object Number: 1892160  Size: SH
  36. Position and install the power brake booster vacuum hose (2) to the intake manifold.
  37. Position the power brake booster vacuum hose clamp at the intake manifold.
  38. Install the power brake booster vacuum hose to the clamp (2) to the generator control module coolant outlet hose.
  39. Install the battery tray. Refer to Battery Tray Replacement .
  40. Fill the cooling system. Refer to Cooling System Draining and Filling .
  41. Connect the hybrid battery. Refer to Hybrid Battery Service Disconnect/Connect .
  42. If the generator control module was replaced, program the NEW module. Refer to Control Module References .
  43. Using a Tech 2, command an autostart in order to verify that the system is working properly.