GM Service Manual Online
For 1990-2009 cars only

Fuel Pump Module Replacement Sedan

Tools Required

J 45722 Fuel Sender Lock Ring Wrench

Removal Procedure


    Object Number: 1790125  Size: SH
  1. Remove the fuel tank. Refer to Fuel Tank Replacement .
  2. Disconnect the fuel tank fuel pump module wiring harness electrical connectors (1, 2) from the fuel pressure sensor and the module.
  3. Disconnect the fuel tank fuel pump module wiring harness electrical connector (3) from the EVAP canister vent solenoid.

  4. Object Number: 1790153  Size: SH
  5. Remove the EVAP emission canister vent pipe from the retaining features (1) built into the fuel tank.

  6. Object Number: 1791653  Size: SH
  7. Reposition the EVAP emission canister vent pipe enough in order to install the J 45722 .
  8. Install the J 45722 to the fuel pump module lock ring.

  9. Object Number: 1642096  Size: SH

    Notice: Avoid damaging the lock ring. Use only J-45722 to prevent damage to the lock ring.

    Notice: Do Not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints.

    Important: Do NOT use impact tools. Significant force will be required to release the lock ring. The use of a hammer and screwdriver is not recommended. Secure the fuel tank in order to prevent fuel tank rotation.

  10. Using the J 45722 and a long breaker-bar, rotate the lock ring in a counterclockwise direction in order to unlock the lock ring.

  11. Object Number: 1790160  Size: SH
  12. Remove the J 45722 from the fuel pump module lock ring.
  13. Lift the fuel pump module up slightly in order to disconnect the fuel tank vent pipe quick connect fitting (1) from the module cover. Refer to Plastic Collar Quick Connect Fitting Service .

  14. Object Number: 1791658  Size: SH
  15. Raise the fuel pump module up from the fuel tank. Tilt the module in order to allow the fuel level sensor arm and float to clear the module opening.
  16. Remove the fuel pump module.
  17. Remove and discard the fuel pump module seal.
  18. Clean the fuel pump module sealing surfaces.

Installation Procedure

Caution: Drain the fuel from the fuel sender assembly into an approved container in order to reduce the risk of fire and personal injury. Never store the fuel in an open container.

Important: 

   • Some lock rings were manufactured with "DO NOT REUSE" stamped into them. These lock rings may be reused if they are not damaged or warped.
   • Inspect the lock ring for damage due to improper removal or installation procedures. If damage is found, install a NEW fuel pump module.
   • Inspect the lock ring for flatness as best as possible. If the lock ring is warped, replace the fuel pump module.


    Object Number: 1791658  Size: SH
  1. Clean any contamination from the male pipe ends of the fuel pump module.
  2. Place a NEW fuel tank module seal onto the fuel tank.
  3. Insert the fuel pump module into the fuel tank allowing the sensor arm and float to clear the module opening.
  4. Lower the module down into the fuel tank until the fuel tank vent pipe quick connect fitting can be connected.

  5. Object Number: 1790160  Size: SH
  6. Connect the fuel tank vent pipe quick connect fitting (1) at the module cover. Refer to Plastic Collar Quick Connect Fitting Service .
  7. Press the fuel tank module downward.

  8. Object Number: 1791653  Size: SH
  9. Reposition the EVAP emission canister vent line enough to install the J 45722
  10. Install the J 45722 to the fuel pump module lock ring.

  11. Object Number: 1642096  Size: SH

    Important: Ensure that the lock ring is installed with the correct side facing upward. A correctly installed lock ring will only turn in a clockwise direction.

  12. Using the J 45722 and a long breaker-bar, rotate the lock ring in a clockwise direction in order the lock the lock ring.
  13. Remove the J 45722 from the fuel pump module lock ring.

  14. Object Number: 1790153  Size: SH
  15. Install the EVAP emission canister vent pipe to the retaining features (1) built into the fuel tank.

  16. Object Number: 1790125  Size: SH
  17. Connect the fuel tank fuel pump module wiring harness electrical connector (3) to the EVAP canister vent solenoid.
  18. Connect the fuel tank fuel pump module wiring harness electrical connectors (1, 2) to the fuel pressure sensor and the module.
  19. Install the fuel tank. Refer to Fuel Tank Replacement .

Fuel Pump Module Replacement Maxx

Tools Required

J 45722 Fuel Sender Lock Ring Wrench

Removal Procedure


    Object Number: 1796271  Size: SH
  1. Remove the fuel tank. Refer to Fuel Tank Replacement .
  2. Disconnect the fuel tank fuel pump module wiring harness electrical connectors (1, 2) from the fuel pressure sensor and the module.

  3. Object Number: 1795288  Size: SH
  4. Disconnect the fuel tank vent pipe quick connect fittings (3, 4) from the module. Refer to Plastic Collar Quick Connect Fitting Service .

  5. Object Number: 1790153  Size: SH
  6. Remove the fuel feed pipe from the retaining features (2, 4) built into the fuel tank.

  7. Object Number: 1796288  Size: SH
  8. Install the J 45722 to the fuel pump module lock ring.

  9. Object Number: 1642096  Size: SH

    Notice: Avoid damaging the lock ring. Use only J-45722 to prevent damage to the lock ring.

    Notice: Do Not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints.

    Important: Do NOT use impact tools. Significant force will be required to release the lock ring. The use of a hammer and screwdriver is not recommended. Secure the fuel tank in order to prevent fuel tank rotation.

  10. Using the J 45722 and a long breaker-bar, rotate the lock ring in a counterclockwise direction in order to unlock the lock ring.

  11. Object Number: 1796294  Size: SH
  12. Remove the J 45722 from the fuel pump module lock ring.
  13. Lift the fuel pump module up slightly in order to disconnect the fuel tank vent pipe quick connect fitting (1) from the module cover. Refer to Plastic Collar Quick Connect Fitting Service .

  14. Object Number: 1796302  Size: SH
  15. Raise the fuel pump module up from the fuel tank. Tilt the module in order to allow the fuel level sensor arm and float to clear the module opening.
  16. Remove the fuel pump module.
  17. Remove and discard the fuel pump module seal.
  18. Clean the fuel pump module sealing surfaces.

Installation Procedure

Caution: Drain the fuel from the fuel sender assembly into an approved container in order to reduce the risk of fire and personal injury. Never store the fuel in an open container.

Important: 

   • Some lock rings were manufactured with "DO NOT REUSE" stamped into them. These lock rings may be reused if they are not damaged or warped.
   • Inspect the lock ring for damage due to improper removal or installation procedures. If damage is found, install a NEW fuel pump module.
   • Inspect the lock ring for flatness as best as possible. If the lock ring is warped, replace the fuel pump module.


    Object Number: 1796302  Size: SH
  1. Clean any contamination from the male pipe ends of the fuel pump module.
  2. Place a NEW fuel tank module seal onto the fuel tank.
  3. Insert the fuel pump module into the fuel tank allowing the sensor arm and float to clear the module opening.
  4. Lower the module down into the fuel tank until the fuel tank vent pipe quick connect fitting can be connected.

  5. Object Number: 1796294  Size: SH
  6. Connect the fuel tank vent pipe quick connect fitting (1) at the module cover. Refer to Plastic Collar Quick Connect Fitting Service .
  7. Press the fuel tank module downward.

  8. Object Number: 1796288  Size: SH
  9. Install the J 45722 to the fuel pump module lock ring.

  10. Object Number: 1642096  Size: SH

    Important: Ensure that the lock ring is installed with the correct side facing upward. A correctly installed lock ring will only turn in a clockwise direction.

  11. Using the J 45722 and a long breaker-bar, rotate the lock ring in a clockwise direction in order the lock the lock ring.
  12. Remove the J 45722 from the fuel pump module lock ring.

  13. Object Number: 1790153  Size: SH
  14. Install the fuel feed pipe to the retaining features (2, 4) built into the fuel tank.

  15. Object Number: 1795288  Size: SH
  16. Connect the fuel tank vent pipe quick connect fittings (3, 4) to the module. Refer to Plastic Collar Quick Connect Fitting Service .

  17. Object Number: 1796271  Size: SH
  18. Connect the fuel tank fuel pump module wiring harness electrical connectors (1, 2) to the fuel pressure sensor and the module.
  19. Install the fuel tank. Refer to Fuel Tank Replacement .