Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category |
DTC Descriptors
DTC B1565 00: Mirror DIP Button StuckDTC B2755 00: Memory Button 1 Stuck
DTC B2760 00: Memory Button 2 Stuck
DTC B3599 00: Memory Button 3 Stuck
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Memory Seat Switch 12 Volt Reference | 1, 2 | 1, 2 | -- | -- |
Memory Mirror Dip Signal | 1, 2 | 2 | B1565 00 | -- |
Memory Seat Signal 1 | 1, 2 | 1 | B2755 00 | -- |
Memory Seat Signal 2 | 1, 2 | 1 | B2760 00 | -- |
Memory Seat Signal 3 | 1, 2 | 1 | B3599 00 | -- |
Memory Mirror Switch Signal M | 1, 2 | 2 | B2765 01 | -- |
Memory Seat Switch Signal 1 | 1, 2 | 1 | B1390 01 | -- |
Memory Seat Switch Signal 2 | 1, 2 | 1 | B1400 01 | -- |
Memory Seat Switch Signal 3 | 1, 2 | 1 | B1410 01 | -- |
1. Memory recall is inoperative 2. Memory mirror recall inoperative | ||||
Circuit/System Description
Reference voltage from the seat interface module (SIM) is supplied at all times to the memory seat switch. When a memory recall switch is pressed, reference voltage is applied through the switch contacts and the signal circuit to the SIM indicating the memory recall request. The SIM serves as a interface and applies a reference voltage through the appropriate memory signal circuit to the memory seat module (MSM) indicating the memory seat request. The MSM then commands the driver seat motors and the exterior mirrors to move to the appropriate seat and mirror positions stored in memory.
Conditions for Running the DTC
The MSM is active.
Conditions for Setting the DTC
B1565 00
If the memory button M switch signal is active for greater than 60 seconds this DTC will set.
B2755 00
If the memory 1 switch signal is active for greater than 60 seconds this DTC will set.
B2760 00
If the memory 2 switch signal is active for greater than 60 seconds this DTC will set.
B3599 00
If the memory 3 switch signal is active for greater than 60 seconds this DTC will set.
Action Taken When the DTC Sets
The memory recall function for the particular memory button is disabled this DTC will set.
Conditions for Clearing the DTC
| • | The current DTC will clear when the switch circuit setting the DTC is no longer active. |
| • | The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Memory Seats Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, observe the scan tool MSM Input parameters listed below while pressing the appropriate memory 1, 2, 3, and M switches. The readings should change between Not Pressed and Pressed.
| • | Memory 1 Button |
| • | Memory 2 Button |
| • | Memory 3 Button |
| • | Memory M Button |
Circuit/System Testing
- Ignition OFF, disconnect the X3 harness connector at the MSM.
- Connect a test lamp between the appropriate signal circuit listed below and ground:
- Ignition ON, command the appropriate memory position listed below ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, replace the MSM.
| • | Memory 1 terminal 9 |
| • | Memory 2 terminal 8 |
| • | Memory 3 terminal 19 |
| • | Memory M terminal 19 |
| • | Button 1 Input |
| • | Button 2 Input |
| • | Button 3 Input |
| • | Button M Input |
| ⇒ | If the test lamp is always ON, test the signal circuit for a short to voltage. If the circuit tests normal replace the SIM. |
| ⇒ | If the test lamp is always OFF, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal replace the SIM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for SIM and MSM replacement, setup, and programming
