EBCM Control Module Scan Tool Output Controls
Scan Tool Output Control | Additional Menu Selection(s) | Description |
|---|---|---|
ABS Motor Test | -- | Used in order to command the ABS pump motor On or Off. |
Automated Bleed Procedure | -- | Used in order to bleed ABS hydraulics. Refer to Antilock Brake System Automated Bleed Procedure . |
LF Inlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
LF Outlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
LR Inlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
LR Outlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
RF Inlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
RF Outlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
RR Inlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
EBCM Control Module Scan Tool Output Controls
Parameter | Operating Conditions | Expected Value | Definition |
|---|---|---|---|
Ignition is ON, engine OFF, and vehicle is stationary | |||
ABS Active | -- | Yes | The scan tool displays Yes/No. The scan tool displays No when not active. |
-- | No | ||
ABS Failed | -- | Yes | The scan tool will display Yes/No depending on the state of the ABS indicator. |
-- | No | ||
Battery Voltage | -- | 12 Volts | The scan tool displays 0-14 Volts. The scan tool displays approximately 12 Volts when the ignition is ON. |
Brake Fluid Pressure Sensor Input | Brake applied | 0.5V | The scan tool displays 0-5 Volts. The scan tool displays approximately 0.5 Volts when the ignition is ON. |
Engine running, brake applied | 1.5V | ||
Brake Switch | Brake pedal applied | 0.5V | The scan tool displays 0-5 Volts. The scan tool displays approximately 0.5 Volts when the ignition is ON and the brake pedal is not applied. |
Brake pedal not applied | 0.7V | ||
Delivered Torque | Engine OFF | 88% | The scan tool displays 0-100 percent. The scan tool displays the duty cycle of the Delivered Torque PWM signal. The duty cycle of the signal is used to transmit how much engine torque the ECM is delivering. Normal values are between 10 and 90 percent duty cycle. |
Engine idling | 10% | ||
EBD Failed | -- | Yes | The scan tool displays Yes/No. The failed status of the EBD. Indicates if the EBCM disabled EBD due to a malfunction. |
-- | No | ||
ESP Active | -- | Yes | The scan tool displays Yes/No. The scan tool displays Yes when ESP is active, and No when ESP is inactive. |
-- | No | ||
ESP Failed | -- | Yes | The scan tool will display Yes/No depending on the state of the ABS indicator. |
-- | No | ||
ESP Off Request | TCS/ESP Switch activated | Active | The scan tool will display Active/Inactive depending on the position of the TCS/ESP Switch. |
TCS/ESP Switch deactivated | Inactive | ||
FL Inlet Valve Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the left front inlet valve solenoid is commanded on. |
-- | Inactive | ||
FL Inlet Valve Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the left front inlet valve solenoid. |
-- | Inactive | ||
FL Inlet Valve Heat Protection | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of left front inlet valve heat protection. |
-- | Inactive | ||
FL Outlet Valve Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the left front outlet valve solenoid is commanded on. |
-- | Inactive | ||
FL Outlet Valve Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the left front outlet valve solenoid. |
-- | Inactive | ||
FL Outlet Valve Heat Protection | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of left front outlet valve heat protection. |
-- | Inactive | ||
FL Wheel Acceleration | -- | 0.000 m/s² (0.000 ft/s²) | The scan tool displays 0-XXX m/s² . The scan tool displays 0 m/s² (0 ft/s²) when the vehicle is not moving or is moving at speeds less than or equal to 0 m/s² (0 ft/s²). |
FR Wheel Acceleration | -- | ||
FL/FR TC/ESP Priming Valve Commanded | -- | Active | The scan tool will display Active/Inactive. The scan tool displays Active when the FL/FR TC/ESP priming valve is commanded on. |
-- | Inactive | ||
FL/FR TC/ESP Priming Valve Feedback | -- | Active | The scan tool displays Active/Inactive. The scan tool displays active when FL/FR TC/ESP priming valve feedback is commanded on. |
-- | Inactive | ||
FL/FR TC/ESP Switch Over Valve Commanded | -- | Active | The scan tool will display Active/Inactive. The scan tool displays Active when the FL/FR TC/ESP switch over valve is commanded on. |
-- | Inactive | ||
FL/FR TC/ESP Switch Over Valve Feedback | -- | Active | The scan tool will display Active/Inactive. The scan tool displays Active when the FL/FR TC/ESP switch over valve feedback is commanded on. |
-- | Inactive | ||
Front Left Wheel Speed | -- | 0 km/h (0 mph) | The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph). |
Front Right Wheel Speed | -- | ||
FR Inlet Valve Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the right front inlet valve solenoid is commanded on. |
-- | Inactive | ||
FR Inlet Valve Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the right front inlet valve solenoid. |
-- | Inactive | ||
FR Inlet Valve Heat Protection | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of right front inlet valve heat protection. |
-- | Inactive | ||
FR Outlet Valve Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the right front outlet valve solenoid is commanded on. |
-- | Inactive | ||
FR Outlet Valve Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the right front outlet valve solenoid. |
-- | Inactive | ||
FR Outlet Valve Heat Protection | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of right front outlet valve heat protection. |
-- | Inactive | ||
Lateral Acceleration Input | -- | 2.5V | The scan tool will display 0-5 Volts. The scan tool displays approximately 2.5 volts when the ignition is ON, and the vehicle is stationary. |
Pump Relay Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the pump relay is commanded on. |
-- | Inactive | ||
Pump Relay Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the pump relay. |
-- | Inactive | ||
Pump Voltage | -- | Voltage | The scan tool will display Voltage when the pump motor is active. |
Rear Left Wheel Speed | -- | 0 km/h (0 mph) | The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph). |
Rear Right Wheel Speed | -- | ||
Requested Torque | -- | 99% | The scan tool displays 0-100 percent. The scan tool displays the duty cycle of the Requested Torque PWM signal. The duty cycle of the signal is used to transmit how much engine torque the EBCM has requested. |
RL Inlet Valve Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the left rear inlet valve solenoid is commanded on. |
-- | Inactive | ||
RL Inlet Valve Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the left rear inlet valve solenoid. |
-- | Inactive | ||
RL Inlet Valve Heat Protection | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of left rear inlet valve heat protection. |
-- | Inactive | ||
RL Outlet Valve Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the left rear outlet valve solenoid is commanded on. |
-- | Inactive | ||
RL Outlet Valve Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the left rear outlet valve solenoid. |
-- | Inactive | ||
RL Outlet Valve Heat Protection | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of left rear outlet valve heat protection. |
-- | Inactive | ||
RL Wheel Acceleration | -- | 0.000 m/s² (0.000 ft/s²) | The scan tool displays 0-XXX m/s² . The scan tool displays 0 m/s² (0 ft/s²) when the vehicle is not moving or is moving at speeds less than or equal to 0 m/s² (0 ft/s²). |
RR Wheel Acceleration | -- | ||
RL/RR TC/ESP Priming Valve Commanded | -- | Active | The scan tool displays Active when the RL/RR TC/ESP priming valve is commanded on. |
-- | Inactive | ||
RL/RR TC/ESP Priming Valve Feedback | -- | Active | The scan tool displays Active when the RL/RR TC/ESP priming valve feedback jis commanded on. |
-- | Inactive | ||
RL/RR TC/ESP Switch Over Valve Commanded | -- | Active | The scan tool displays Active when the RL/RR TC/ESP switch over valve is commanded on. |
-- | Inactive | ||
RL/RR TC/ESP Switch Over Valve Feedback | -- | Active | The scan tool displays Active when the RL/RR TC/ESP switch over valve feedback is commanded on. |
-- | Inactive | ||
RR Inlet Valve Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the right rear inlet valve solenoid is commanded on. |
-- | Inactive | ||
RR Inlet Valve Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the right rear inlet valve solenoid. |
-- | Inactive | ||
RR Inlet Valve Heat Protection | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of right rear inlet valve heat protection. |
-- | Inactive | ||
RR Outlet Valve Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the right rear outlet valve solenoid is commanded on. |
-- | Inactive | ||
RR Outlet Valve Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the right rear outlet valve solenoid. |
-- | Inactive | ||
RR Outlet Valve Heat Protection | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of right rear outlet valve heat protection. |
-- | Inactive | ||
Steering Angle | Steering wheel at centre | 0° | The scan tool will display Steering Angle Sensor. The scan tool will display the signal received from the Steering Angle Sensor. |
Steering wheel at left lock | -500° | ||
Steering wheel at right lock | 500° | ||
Valve Relay Commanded | -- | Active | The scan tool displays Active/Inactive. The scan tool displays Active when the valve relay is commanded on. |
-- | Inactive | ||
Valve Relay Feedback | -- | Active | The scan tool displays Active/Inactive. Indicates the actual state of the valve relay. |
-- | Inactive | ||
Yaw Rate sensor Input | -- | 2.5V | The scan tool will display Volts, depending on the angle of the vehicle. |
