GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    •  Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    •  Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of the diagnostic category.

DTC Descriptors

DTC P1546: Air Conditioning Compressor Feedback Circuit Low

DTC P1539: Air Conditioning Compressor Feedback Circuit High

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

A/C Compressor Clutch Feedback

P1546

P1546

P1539

--

Circuit/System Description

The A/C compressor clutch relay is monitored by the ECM/PCM through the A/C compressor clutch relay feedback circuit.

Conditions for Running the DTC

    • Engine is running.
    • Any of the conditions for setting the DTC are met for 15 seconds.
    • Battery voltage is between 11-18 volts.

Conditions for Setting the DTC

The ECM/PCM detects that the A/C compressor clutch is not on after an A/C request has been made.

Action Taken When the DTC Sets

    • The ECM will not illuminate the malfunction indicator lamp (MIL)
    • The ECM stores the Failure Records.
    • The A/C compressor clutch is disabled.

Conditions for Clearing the DTC

    • The history DTC will clear after 40 consecutive ignition cycles have occurred without a malfunction.
    • The DTC will become history if the ECM no longer detects a failure.

Reference Information

Schematic Reference

HVAC Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Manual HVAC Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Ignition ON, observe the scan tool A/C Request Signal parameter while changing the mode switch from OFF to Defrost, the reading should change from No to Yes.
  2. If the reading does not change while switching between the commanded states, refer to A/C Request Malfunction.
  3. Observe the scan tool A/C Compressor Cycling Switch parameter. The reading should be normal.
  4. If not the specified value, refer to Low Pressure Switch Malfunction.
  5. Command the A/C relay ON and OFF with a scan tool. Observe the A/C compressor operation, the A/C compressor clutch should engage and disengage when changing between the commanded states.
  6. If the A/C compressor does not engage or does not disengage, refer to A/C Compressor Malfunction.

Circuit/System Testing

A/C Request Malfunction

  1. Ignition OFF, disconnect the harness connector at the A/C high pressure switch.
  2. Ignition ON, mode set to Defrost, verify that a test lamp illuminates between the control circuit terminal B and ground.
  3. If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal refer to Blower Motor Malfunction.
  4. Verify the scan tool A/C Request Signal parameter is No.
  5. If not the specified value, test the signal circuit terminal A for a short to voltage. If the circuit tests normal, replace the ECM/PCM.
  6. Install a 3A fused jumper wire between the signal circuit terminal A and the control circuit terminal B. Verify the scan tool A/C Request Signal parameter is Yes.
  7. If not the specified value, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the ECM/PCM.
  8. If all circuits test normal, test or replace the A/C high pressure switch.

Low Pressure Switch Malfunction

  1. Ignition OFF, disconnect the harness connector at the A/C low pressure switch.
  2. Test for less than 1 ohm between the ground circuit terminal A and ground.
  3. If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Verify the scan tool A/C Compressor Cycling Switch parameter is Normal.
  5. If not the specified value, test the signal circuit terminal B for short to ground. If the circuit tests normal, replace the ECM/PCM.
  6. Install 3A fuse jumper between the signal circuit terminal B and the ground circuit terminal A. Verify the scan tool A/C Compressor Cycling Switch parameter is Low Pressure.
  7. If not the specified value, test the signal circuit for short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM/PCM.
  8. If all circuits test normal, test or replace the A/C low pressure switch.

A/C Compressor Malfunction

  1. Ignition OFF, disconnect the A/C compressor clutch relay.
  2. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.
  3. If the test lamp illuminates, test the control circuit for a short to voltage.
  4. Verify that a test lamp illuminates between the ignition circuit terminal 86 and ground.
  5. If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition circuit breaker/fuse is open, test or replace the A/C compressor clutch relay.
  6. Verify that a test lamp illuminates between the B+ circuit terminal 30 and ground.
  7. If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  8. Disconnect the harness connector at the A/C compressor clutch.
  9. Test for less than 1.0 ohm between the A/C compressor clutch ground circuit terminal A and ground.
  10. If greater than the specified range, test the ground circuit for an open/high resistance.
  11. Connect the harness connector at the A/C compressor clutch.
  12. Connect a 10A fused jumper wire between the B+ circuit terminal 30 and the control circuit terminal 87. Verify the A/C compressor clutch is activated.
  13. If the A/C compressor clutch does not activate, test the control circuit for an open/high resistance. If the circuit tests normal, replace the A/C compressor.
  14. Connect a test lamp between the ignition circuit terminal 86 and the control circuit terminal 85.
  15. Command the A/C relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
  16. If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM/PCM.
    If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM/PCM.
  17. If all circuits test normal, test or replace the A/C compressor clutch relay.

Component Testing

Relay Test

  1. Ignition OFF, disconnect the A/C compressor clutch relay.
  2. Test for 60-180 ohms between terminals 85 and 86.
  3. If the resistance is not within the specified range, replace the relay.
  4. Test for infinite resistance between the following terminals:
  5. • 30 and 86
    • 30 and 87
    • 30 and 85
    • 85 and 87
    If not the specified value, replace the relay.
  6. Install a 30-amp fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms between terminals 30 and 87.
  7. If greater than the specified range, replace the relay.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Relay Replacement
    •  Compressor Clutch Plate/Hub Assembly Replacement
    •  Air Conditioning (A/C) High Pressure Switch Replacement
    •  Air Conditioning Cycling Switch Replacement
    •  Control Module References for ECM/PCM replacement, setup, and programming