GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2002 🢒 Impala 🢒 Body and Accessories 🢒 Data Link Communications 🢒 Inflatable Restraint Sensing and Diagnostic Module Replacement

Inflatable Restraint Sensing and Diagnostic Module Replacement AK5

Removal Procedure

CAUTION: Be careful when you handle a sensing and diagnostic module (SDM). Do not strike or jolt the SDM. Before applying power to the SDM:

   • Remove any dirt, grease, etc. from the mounting surface
   • Position the SDM horizontally on the mounting surface
   • Point the arrow on the SDM toward the front of the vehicle
   • Tighten all of the SDM fasteners and SDM bracket fasteners to the specified torque value
Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.


    Object Number: 300146 Size: SH
  1. Disable the SIR system. Refer to Disabling the SIR System .
  2. Remove the passenger front seat. Refer to Front Seat Replacement - Bucket in Seats.
  3. Remove the passenger front carpet retainer, then roll back the carpet.
  4. Remove the connector position assurance (CPA) from the inflatable restraint sensing and diagnostic module (SDM) wiring harness connector.
  5. Disconnect the SDM wiring harness connector from the SDM.

    6. Object Number: 300147 Size: SH
  6. Remove the SDM mounting fasteners (3).
  7. Remove the SDM (1) from the floor pan (2).

Installation Procedure

    Object Number: 300147 Size: SH
  1. Install the SDM (1) to the floor pan (2).

    2. Notice: Refer to Fastener Notice in the Preface section.

  2. Install the SDM mounting fasteners (3).

    3. Tighten
    Tighten the fasteners to 10 N·m (89 lb in).


    Object Number: 300146 Size: SH
  3. Install the SDM wiring harness connector to the SDM.
  4. Install the connector position assurance (CPA) to the SDM wiring harness connector.
  5. Install the carpet and the passenger front carpet retainer.
  6. Install the passenger front seat. Refer to Front Seat Replacement - Bucket in Seats.

    7. Important: The AIR BAG indicator may remain ON after the SDM has been replaced. DTC B1001 may set requiring the SDM part number to be set in multiple modules. If the indicator remains ON after enabling the SIR system, perform the diagnostic system check and follow the steps thoroughly to ensure that the SDM is set properly.

  7. Enable the SIR system. Refer to Enabling the SIR System .

Inflatable Restraint Sensing and Diagnostic Module Replacement AJ7

Removal Procedure

CAUTION: Be careful when you handle a sensing and diagnostic module (SDM). Do not strike or jolt the SDM. Before applying power to the SDM:

   • Remove any dirt, grease, etc. from the mounting surface
   • Position the SDM horizontally on the mounting surface
   • Point the arrow on the SDM toward the front of the vehicle
   • Tighten all of the SDM fasteners and SDM bracket fasteners to the specified torque value
Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.


    Object Number: 300148 Size: SH
  1. Disable the SIR system. Refer to Disabling the SIR System .
  2. Remove the passenger front seat. Refer to Front Seat Replacement - Bucket in Seats.
  3. Remove the passenger front carpet retainer, then roll back the carpet.
  4. Remove the connector position assurance (CPA) from the inflatable restraint sensing and diagnostic module (SDM) 8-way wiring harness connector.
  5. Disconnect the SDM 8-way wiring harness connector from the SDM.
  6. Remove the connector position assurance (CPA) from the SDM 18-way wiring harness connector (2).
  7. Disconnect the SDM 18-way wiring harness connector from the SDM.

    8. Object Number: 300149 Size: SH
  8. Remove the SDM mounting fasteners (3).
  9. Remove the SDM (1) from the floor pan (2).

Installation Procedure

    Object Number: 300149 Size: SH
  1. Install the SDM (1) to the floor pan (2).

    2. Notice: Refer to Fastener Notice in the Preface section.

  2. Install the SDM mounting fasteners (3).

    3. Tighten
    Tighten the fasteners to 10 N·m (89 lb in).


    Object Number: 300148 Size: SH
  3. Install the SDM 18-way wiring harness connector to the SDM.
  4. Install the connector position assurance (CPA) to the SDM 18-way wiring harness connector.
  5. Install the SDM 8-way wiring harness connector to the SDM.
  6. Install the connector position assurance (CPA) to the SDM 8-way wiring harness connector.
  7. Install the carpet and the passenger front carpet retainer.
  8. Install the passenger front seat. Refer to Front Seat Replacement - Bucket in Seats.

    9. Important: The AIR BAG indicator may remain ON after the SDM has been replaced. DTC B1001 may set requiring the SDM part number to be set in multiple modules. If the indicator remains ON after enabling the SIR system, perform the diagnostic system check and follow the steps thoroughly to ensure that the SDM is set properly.

  9. Enable the SIR system. Refer to Enabling the SIR System .