Front Side Door Outside Handle Replacement Impala

Important: The outside handles have adjustable lock rod. This allows for adjustment of the amount of travel needed to operate the outside handle.

1. Position the window completely up.
2. Remove the front door trim panel. Refer to Front Side Door Trim Panel Replacement .
3. Remove the front door water deflector. Refer to Front Side Door Water Deflector Replacement .



4. Remove the front door rear window channel bolt.



5. Remove the front door rear window channel from the front door slot by pulling downward to disengage the retainer clip.



6. Remove the outside door handle rod-to-lock clip from the lock.
7. Remove the front door outside handle lock cylinder. Refer to Door Lock Cylinder Replacement .



8. Remove the hole plug to access to one of the two bolts that attach the outer door handle.
9. Remove the front door outside door handle from the door.



10. Remove the front door outside door handle rod from the handle.

1. Install the lockcylinder retainer clip to door handle.



2. Install the front door handle rod to the door handle.



3. Install the front outside door handle to the door.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the front door outside door handle bolts.

Tighten
Tighten the front door outside door handle bolts to 10 N·m (89 lb in).

5. Install the front door outside handle lockcylinder. Refer to Door Lock Cylinder Replacement .
6. Install a NEW outside handle rod-to-lock clip onto the door lock lever.

•	Position the outside door handle rod in the clip to eliminate any free play in the outside door handle.

•	Install the clip cover over the threaded outside door handle rod.




7. Install the front door rear window channel to the front door, ensuring that the up clip is engaged to the upper channel.



8. Install the front door rear window channel bolt.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

9. Install the front door rear window channel bolt.

Tighten
Tighten the front door rear window channel bolt to 10 N·m (89 lb in).

10. Install the access hole plug.
11. Install the front door water deflector. Refer to Front Side Door Water Deflector Replacement .
12. Install the front door trim panel. Refer to Front Side Door Trim Panel Replacement .

Front Side Door Outside Handle Replacement Monte Carlo

Important: The outside handles have adjustable lock rod. This allows for adjustment of the amount of travel needed to operate the outside handle.

1. Position the window completely up.
2. Remove the front door trim panel. Refer to Front Side Door Trim Panel Replacement .
3. Remove the front door water deflector. Refer to Front Side Door Water Deflector Replacement .



4. Remove the front door rear window channel bolt.



5. Remove the front door rear window channel from the front door slot by pulling downward to disengage the retainer clip.



6. Remove the outside door handle rod-to-lock clip from the lock.
7. Remove the front door outside handle lockcylinder. Refer to Door Lock Cylinder Replacement .



8. Remove the hole plug to access to one of the two bolts that attach the outer door handle.
9. Remove the front door outside door handle from the door.



10. Remove the front door outside door handle rod from the handle.

1. Install the lockcylinder retainer clip to door handle.



2. Install the front door handle rod to the door handle.



3. Install the front outside door handle to the door.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the front door outside door handle bolts.

Tighten
Tighten the front door outside door handle bolts to 10 N·m (89 lb in).

5. Install the front door outside handle lockcylinder. Refer to Door Lock Cylinder Replacement .
6. Install a NEW outside handle rod-to-lock clip onto the door lock lever.

•	Position the outside door handle rod in the clip to eliminate any free play in the outside door handle.

•	Install the clip cover over the threaded outside door handle rod.




7. Install the front door rear window channel to the front door, ensuring that the up clip is engaged to the upper channel.



8. Install the front door rear window channel bolt.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

9. Install the front door rear window channel bolt.

Tighten
Tighten the front door rear window channel bolt to 10 N·m (89 lb in).

10. Install the access hole plug.
11. Install the front door water deflector. Refer to Front Side Door Water Deflector Replacement .
12. Install the front door trim panel. Refer to Front Side Door Trim Panel Replacement .