Schematic Reference: HVAC Schematics

Connector End View Reference: HVAC Connector End Views

DEFINITION: The temperature cannot be adjusted, or the heating is insufficient.

1

Did you perform the HVAC Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - HVAC Systems - Manual

1. Turn ON the ignition, with the engine OFF.
2. Place the mode switch in any position except OFF.
3. Place the blower motor switch in each speed position.

Does the blower motor operate in each speed position?

--

Go to Step 3

Go to Blower Motor Inoperative

Is the airflow sufficient from the correct outlets for each mode?

--

Go to Step 4

Go to Blower Motor Malfunction

Inspect the cooling system for the following conditions:

Refer to Heating Performance Diagnostic in Heating, Ventilation and Air Conditioning.

Did you find and correct the condition?

--

Go to Step 17

Go to Step 5

1. Start the engine.
2. Place the blower motor switch in the OFF position.

Does the A/C compressor operate?

--

Go to HVAC Compressor Clutch Does Not Disengage

Go to Step 6

1. Place the headlamp switch in the PARK position.
2. Place the instrument panel dimmer switch in the brightest position.
3. Place the mode switch in the vent position.
4. Place the blower motor switch in the maximum speed position.
5. Place the outside air switch in the ON position.
6. Place the recirculation switch in the ON position.

Does the recirculation door operate properly?

--

Go to Step 7

Go to Air Delivery Improper

7

1. Observe the drive shaft for the left and right air temperature actuator
2. Place the air temperature switch from the coldest position to the warmest position.

Does the drive shaft of the left and right air temperature actuator rotate?

--

Go to Step 8

Go to Step 9

Inspect the left and right air temperature door and the left and right air temperature actuator for the following conditions:

Did you find and correct the condition?

--

Go to Step 18

Go to Step 9

Test the ignition 3 voltage circuit of the suspect air temperature actuator for an open or a high resistance. Refer to Circuit Testing and Wiring Repairs a in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 10

Test the ground circuit of the suspect air temperature actuator for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 11

Test the suspect air temperature door position signal circuit of the air temperature actuator for an open, high resistance, short to ground, or short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 12

12

Important: Ensure that the HVAC control module connector is connected during this step in order to avoid misdiagnosis.

1. Turn ON the ignition, with the engine OFF.
2. Measure the voltage from the suspect air temperature door position signal circuit of the suspect air temperature actuator to a good ground.
3. Place the air temperature switch from the coldest position to the warmest position.

Does the voltage measure within the specified values with a smooth transition between cold and hot?

0-12 V

Go to Step 14

Go to Step 13

Inspect for poor connections at the harness connector of the suspect air temperature actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 14

Inspect the suspect air temperature actuator, door and any attaching linkage for binding or a condition that prevents drive shaft rotation.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 16

Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 17

Replace the suspect air temperature actuator. Refer to Air Temperature Actuator Replacement - Right Side or Air Temperature Actuator Replacement - Left Side .

Did you complete the replacement?

--

Go to Step 18

--

Replace the HVAC control module. Refer to Heater and Air Conditioning Control Replacement .

Did you complete the replacement?

--

Go to Step 18

--

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 2